Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello,
we have a remote control with 7 buttons.
Every button shall wakeup the device from deep sleep.
Beside i will have an interrupt on Button 6 and 7.
So the problem...
I am using nrfconnect 1.5.1 (zephyr/command line) with modem firmware 1.2.3 and believe I have found a fairly serious bug/behavior in the UDP API. It is pretty easy "crash...
Hi,
I looked at some of the questions on the forum and they didn't give me good advice. Currently all I can do is nrf52832 Security 1 Level 4 and nrf52833 Security 1 Level...
In the nRF5340 product specification version 1.2, I see an internal bandgap reference error range of -1.8/+0.5%.
In the nRF5340 product specification version 1.2, I see...
There're 2 things annoying me:
1.What's the right way to use VS code, does every time I need to open VSCode in ToolChain Manager?
I just want to open VSCode directly,...
Hello i am working with the example ble_app_uart and i have created one new service and two characteristics. The firmware was working fine with no errors. However my computer...
Hi,
This is the follow up on this question , I'm not sure how it was closed.
I'm getting different execution times (not transmission time, like mentioned in the answer...
Hi,
I want to debug my nrf5340 custom board with logger method. I have tried to follow the Nordic's nrf connect SDK course. And I have written the code and just flashed...
The problem i having seems to be tricky and i spent hours trying to figure out whats happening. So, i will try to put all details possible. Im two days with this issue and...
Hi there,
I faced this issue while I was setting up a test through two UART0 & UART1 ports on NRF5340 chip, using baudrate 1000,000.
Here is the setup:
UART0 &...
I currently use nrfConnect on android to download firmware to nrf52832s. I am just getting started with nRFUtil and the dongle.
If I understand correctly, I should be able...
I have a nRF52 DK from DigiKey that I've been evaluating and I ran into an issue: I had a custom app that was talking through Bluetooth and sharing some custom characteristics...
Hi, I'm using NXP LM75B temprature sensor based on nRF SDK's example code.
I would like to save power on this sensor.
I have prepared the code as follows:
Following...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
I'm developing for nRF52832, SDK 17.0.2 and softdevice S312 7.0.1.
After I upgraded from Segger Embedded Studio 6.22a to 6.30 I found that turning on any compiler optimisation...
