Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi, I tried httpsClient sample on nrf9160dk. It did not work because I can not change APN settings on proj.conf. I attached my screen. What is the apn config command on new...
I have a simple prototype platform that previously uses nRF51822 which is discontinued. Now I plan to replace the BLE module with nRF52833.
Previously developed firmware...
Hi everyone ,
I want to perform DFU of SD+Bl+APP via UART.
I use nrfutil version 6.1.3.
The Softdevice is s140_nrf52_7.2.0_softdevice.hex and the application is based...
Hello everyone, i'm trying to deal with the ACS714T sensor but i can't find any samples or guide through internet the communication need to be done through ADC and SAADC HAL...
I am using the nrfx_uart and need to disable the receiption. I call nrfx_uart_rx_disable. When done once, the receiption is not working anymore, even when I call nrfx_uart_rx_enable...
I am the digital pcb and fw designer on a project using a dipole antenna defiend by the RF designer ( I have read the posts discouraging that and have taken that into account...
I am studying the ble_beacon example among the examples provided by nordic.
I want to code the beacon's uuid to indicate the mac address.
I studied to find the mac address...
Question: Can UART ASYNC and UART INTERRUPT work together? I want to use async UART along with interrupt driven USB CDC, but I am not able to use both together.
Details...
Hi team,
Note that nRF Sniffer already support nRF52840 dongle, but can that sniffer the BLE5 Advertising extension pack?
How to set the sniffer software?
Thanks!...
Hi,
I'm experimenting with the AoA locator receives IQ data on nRF52833 in ncs1.7.1. It worked well when the locator only received IQ data from one beacon. But when multiple...
Hiya. We're building a custom appliance on top of a Nordic chip that talks to an Android/iOS app developed with Flutter and a custom cross-platform Bluetooth plugin.
We...
Hi guys,
I tried to connect to nRF52832 using the app and it was successful. But when I directly use the BLE in the Android system(android 11) settings to connect to the...
Hi. I am new with nRF52 microcontrollers. I was able to create a project (myproject) in the examples folder and compile it with SEGGER embedded studio. I copied the whole...
Hello
I just downloaded nrf sdk 12.3 and am facing a problem straight away where I couldn't find valid answers that would fix my problems when searching this forum and on...
