Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello,
I'm very unexperienced with low-level programming, so I apologize is some of my questions make little sense.
We have this board that sends telemetry data using...
Dear Support,
I updated the nRF Connect for Desktop's Programmer to v3.0.0 and noticed that it is no longer possible to write a file to a nRF9160 using a Segger jLink without...
I am currently programming an evaluation board to get to know BLE better. Currently I am using the nrf52811 on a custom board.
So far I used an example from nordic to create...
Probably there is already some solution here in the forum, but I couldnt find a fitting one.
My problem: I have custom code on my nRF52840 DK, which is used as an aggregator...
Hi,
I am running a multirole device based on the 'central_and_peripheral_hr' samples of nRF Connect SDK v1.8.0. The device holds a connection as peripheral and it is scanning...
Hi Sir/Miss,
I use nRF52832, softdevice 132 and SDK 17.1.0 to develop.
And, I want to use GPIO to wake up from system off.
We use external pull up resistor in wake up...
I'm testing with the new rev of the nRF52832 (build code QFAAGB on the package), and I'm not able to observe behavior that makes sense to me per the updated product spec....
Currently working on a nrf52dk_nrf52832 kit. I have a SPI flash that I am trying to use - I am using the nrf SDK ncs v1.9.1.
I know I can use any of the GPIO pins for SPI...
Hello
I have a mesh node that needs to broadcast a custom BLE packet
To start advertising I call bt_le_adv_start and it works as expected.
I'm curious about the error...
I've been trying to enable the watchdog as early as possible during boot. I haven't been able to find any way to configure the nrf52832 watchdog to enable itself prior to...
Hello,
I'm in nRF Connect SDK 1.5 and I have to change the baudrate of UART1 at runtime. I have to use Zephyr UART Functions. I have tried the function uart_configure()...
I have a customer that has been using the nRF Connect Mobile app on his iPhone to test his device and its works perfectly and he can do all the functionality he wants including...
Hi.
I am developing using nRF52832 & ST7789 round LCD.(softdevice : s112, SDK version : nRF5_SDK_17.0.0)
Currently, I am trying to develop using the gfx library, but there...
I'm comparing some of the ZBOSS API between what's in the nRF5 SDK for Zigbee and what's in the nRF Connect SDK, and I'm curious about the differences in some cluster list...
