I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
I'm using the nRF52840 on a custom board along with an ESP8266 (ESP-12S) Wi-Fi module.
The ESP module prints out a bunch of information at a weird nonstandard baud...
I am having trouble setting up DFU over BLE in nRF Connect SDK. I am using NCS 1.9.1. I have followed these instructions with my own project on both the nrf52840 devkit and...
Dear All,
We are developing a device based around nRF52840 on a rigid-flex custom PCB that is mounted inside an anodized aluminum cube with one face covered with plastic...
Hello, I'm trying to get an LPN to unprovision itself based off of an external command. I tried to base it off of the examples so I simply call: However after the reset it...
Hi,
I have my device based on the nRF52840, we have manufactured some equipments and we have created our own application to manage connection. Everything is working fine...
Hi all,
we recently had a problem with couple of our boards based on Raytac MDBT50Q-1MV2 (nrf52840 + osc. + antenna). We base our app on Zephyr. After programming some boards...
Hi, I've been tasked with doing some development on the nRF24LE1F on one of our legacy products that was designed many years ago! I'm in process of converting the code to...
Hi,
I'm trying to use UART1 for console and shell, for example to be able to log messages on VCOM0 linked to UART1 of my nRF5340 DK board. The example that I'm testing is...
Hi Nordic team
Customer Delta was running a street lamp project.
For AWS FOTA, they applied a AWS account and firmware update already can work.
However, it looks like...
Hello,
I am developing FW on NRF52840_DK for a BLE Peripheral as a Reader.
Reader to Mobile App Tx size is 32 bytes
Mobile App to Reader Rx size is 133 bytes.
When...
Dear Bluetooth Mesh experts, The firmware contains a proprietary message that sets a node's parameters and returns 100 bytes of data. The Android app sends it as an acknowledged...
Hi
I've configured Zephyr to run BLE host on cpuapp and BLE controller on cpunet, and using RPMsg to communicate between them.
When I call bt_enable() from the app core...
Hello,
I was wondering if there is a way to extract the "Device name" from the scanned advertisement data published by a model on a different node. I want to display the...
I'm trying to enable saving of coredump to flash. I'm running on nrf52840 with NRF SDK 1.6.1.
I have defined the following:
CONFIG_DEBUG_COREDUMP=y
CONFIG_DEBUG_COREDUMP_BACKEND_FLASH_PARTITION...
Hello ,
We are attempting to use the QSPI driver with an MX25 with 2 i/o lines instead of 4, essential SB 10 and 15 on the nrf52840 DK have been cut. However I am not...
