I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi
Is there a possibility to read out the actual RX pointer of the DMA if the amount of chars is not reached?
Start Stop the RX is not really an option and I have no...
Hi everyone! I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice. The nrf go studio can not detect the nrf52832, but...
Hi,
I set sending of Ext. ADV at a periodicity of 500ms and scanning for 100% time by setting same interval and window configuration to 2.56 s.
But I observed that the...
Hi
I have a project to use HID mouse and keyboard at the same time, I have tried , but it really can't work well. I've read the similar question and you don't give the clearly...
Hi
I want to combine mouse and keyboard function together,and I had modify the example of hid mouse,show as below
but the question I meet is that the PC and phone reaction...
Hi,
I am developing an application (Peripheral Sensor device: Acceleration measurement), I have included the characteritsics for the measurement and I am trying to include...
I tried to enable the configuration of Thingy91 to use external sensors. I made following additions:
1. Added the following line to Asset_tracker_V2/K config file : rsource...
Hi,
is it possible for a central device to connect to a peripheral device directly (without using nrf_ble_scan_init( ), nrf_ble_scan_filter_set( ), nrf_ble_scan_filters_enable...
Hello,
I am trying to write some code that sets the BLE Tx power on the nRF52833 SoC.
I have based my code on the sample example code provided at C:\Zypher\v1.7.0\zephyr...
We're using the read authentication trigger to detect when a characteristic is being read, so we can update the value before a read. Is it possible to have a read with zero...
Hello,
at the beginning I want to state, that I have read all the tickets with similar issue, but still can't find any solution to my problem, that's why I'm creating...
Hi!
I was controling a little vibration motor with a mosfet which is activated by a nrf52840Dongle pin. I was using pin 0.17 and it worked pretty well, but now I am trying...
Dear reader
We want to use the floating point unit (FPU) in our project
We are building using the IAR compiler (8.5.x)
We'd like to use the hardware acceleration ...
Hi.
We are working on a project which uses nrF9160DK and nRF5340DK, which works fine on this last one. The problem is that when I tried building on the 9160 using nRF Connect...
