I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
This is the errors , please help, to successfully create .hex file
If you want to look after full log details .......
Building firmware west build --build-dir c:\Users...
I bought a thingy91 module with ibasis scheduler on board. When I made the first installation of the mfw_nrf9160_1.3.1.zip software and the thingy91_asset_tracker_v2_ltem_2022...
I'm building a simple application using I2C to read sensor data (BNO055). I confirmed I2C and my sensor are all configured appropriately and working smoothly, but when I added...
Hi,
I'm using the mqtt_simple example to develop a new application.
I want you to tell me what lines of code I need to add for the nRF9160 to work in the minimum power...
Hi,
I am working with NRF52840 DK, from this i am using KEIL IDE. I got some error while opening the KEIL SW like Cannot set path to software packs. Make sure that RTEPATH...
Hi,
My customer use nRF5340 as their master control IC, which will connect with lots of peripheral.
They are considering about simulate a uart with GPIO.
What's the...
I have designed a custom board for the nrf52840 and upon testing it in the nrf connect sdk (using a JLink), I can only see the board when it's in bootloader mode. When it...
Hi,
I am in the process of migration from SES to Visual Studio; I have imported my project; but it has no active build configuration. When I try and add a build configuration...
I am using 9160 to develop a watch product. During the network test, I found that the description of parameter period tau in CPSMS instruction and xmonitor instruction is...
So, i have created a custom board using the nrf52811 SoC. I tried to upload some bluetooth examples to it, and i can see the device on the nRF connect APP. The problem is...
On firing the following command "$ node cli create-ca-intermediate"
terminal showing error
I am following this link nordicsemiconductor.github.io/.../DeviceCredentials...
Hi support team,
I'm trying to simulate the BDM protocol of the 9s12 chip series. Basically the protocol is as follows: Communication on 1 GPIO pin, output open-drain mode...
Hi,
NCS1.9.1, VSCode, nRF5340DK cannect a NFC tag,
i write text to NFC tag by Adafruit-PN532 with anouher device,
than 5340 mcu how to read the text in NFC tag ?
...
Hi! I would to know how to partition the memory of the board and how to make that secure and trusted. Once I did that there is a way to save some information in that portion...
I'm using a nRF52832 for a product under FAA regulations. The standard requires the BLE module to perform a self-test. What self-test capabilities does the Nordic nRF52 family...
