Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Dear Nordic Team !
I think I found a bug in the ble_db_discovery module of Nordic SDK 15.3.0, maybe other SDKs are affected too. I am implementing a BLE central device for...
I received my NRF52840-DK board, today, from Digi-key. I followed directions in starting it up - power set to USB, switch to on. When I turn it on, all LEDs flash and pressing...
After a lot of stumbling around (the documentation for the ANT+ examples needs to be improved) I finally got some of the ANT+ examples working on my nRF52 DK board. When programmed...
I have developed below I2C code with an RTC timer event handler to sample data from a sensor every 1s. This format is used mainly to save power.
I can see there is a base...
HI
How can I to send 512 characters over BLE NUS?
I saw in Ble uart example this
I received 247data from BLE NUS
can I to receive 512?
how can I do that?
...
Hi,
We are currently going through the Verizon self certify program, using an adaptation of the asset_tracker_v2 firmware on our device. Verizon said to reach out to Nordic...
Look like a hard coded bug in API generated in build\zephyr\include\generated\syscalls\flash.h ?
-- Found BOARD.dts: zephyr/boards/arm/nrf52840dk_nrf52840/nrf52840dk_nrf52840...
Hello! I have a serial device (RN8209 power meter) which is connected by UART to a nRF52832 with 4800 Baud. I am using SDK17 nrfx UARTE to access it, but I have observed,...
We have a custom board with a uBlox Nina-B1 module. Pin 0.05 is connected to an analog switch (NX3DV2567) which powers a microphone and capacitive switch. When the pin is...
Hi everyone,
I am using nrfConnect 3.9.3, And SDK v1.7.0.
I am working on a project based on uart example.
My question is if there are some way for clean/discard all...
I'm unable to get a cloud response using the XPING command with some IoT sim cards on the nRF9160. I've been working with serial_lte_modem projects on this chipset. I've also...
I cannot find any information on how to update mcuboot over SMP when using the immutable bootloader.
I have my NRF52840 setup with the chained bootloader: b0 -> mcuboot...
Hi,
First of all thank you for your support and suggestions.
As I am planning to use nRF52840 SoC in my design, (Project: BLE based Environmental sensor). The circuit...
Hey. In production we are logging PM error events to try to determine the root cause for some unstable connection that keep showing up. We are seeing with high occurrence...
