Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi everyone,
I'm currently using nRF52832 with nRF5DK_V17.1.0 file.
I understand that this question has been risen up quite a lot however, I still do not understand why...
Hello Nordic team,
I am testing a timer using code snippet which Nordic team recommended as a reference. My code is something like this:
uint64_t start, stop;...
Hello,
A nrf52840 central device programmed with Soft-Device S132 and connectivity firmware, the host is interfaced via USB and uses PC-BLE driver API's to communicate with...
Hi,
I'm using nrf52840 DK and android based mobile with nrf connect for mobile app installed.
I would like to execute a freestanding sample code to transfer message between...
Hi Nordic,
I met a issue on BUS FAULT , which caused by queue.
It core dumps that:
[2022-03-22 15:35:12.657] [xxx]index = 6,len = 158 [2022-03-22 15:35:12.660] [xxx...
Hi all,
I'm a beginner and planning to import Android-nRF-Toolbox source code from Github into Android Studio after reading the README by the following steps:
1. I open...
Hi Team
In nRF52
According below picture the only the power on reset and brownout reset can reset SWJ-DP. Do we have any other method to reset the SWJ-DP.
By the way...
Hi there, We have a product using an nRF52832-QFAA, with the SDK15.2.0, the 132 Softdevice, and an application based around the Nordic UART service (nus). Customers are reporting...
Hi everyone,
i'm writing to ask some advice for my NBIOT AWS application with the nRF9160 DK.
I'm currently using the aws_iot sample available as a baseline for my project...
Hello,
We observed that the BLE-Mesh provision logs are happening in FCBs of NV Flash, For my application i need them to be logged on RAM. Kindly suggest how I can achieve...
Hi everyone,
I am working on a project, in which I have n nodes that communicate with each other (peer to peer communication). In addition, each node is able to communicate...
under freestanding applications, which code to use to enable bluetooth on nRF52840 DK kit . Then, it has to pair with android mobile. how i can achieve it.
I see mainline Zephyr is now on v3.0.0 since end of Feb. I assume the bump from 2.7.x to 3.x means substantial changes. When will NCS move to a 3.x zephyr?
I ask this...
Hello.
It is being developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
Previously, I inquired about how to add a value to the characteristic with...
