Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I am using the Nordic PDM library to collect data from a digital microphone. I am currently storing the data in a 1k int16_t buffer and attempting to store the data...
Hi,
I try to install nrfconnectsetup330ia32.exe on my Windows-10 x64 bit computer. The setup program hangs when the progress bar is at about 33%. It just sits there without...
I am currently working on Nrf52840DK board trying to run ble_uart_app. Designed my board and I used BT840 instead of Nrf52840DK . After, code in NRF52840DK is working but...
Using a Thingy!91 (v1.0.0 and v1.4.0, firmware 1.2.3, 1.2.7) I get sometimes (every couple of days) a ENETDOWN when sending data out. Before that ENETDOWN, the device was...
Hello,
I've been working with NRF52840 for a while now. Recently I decided to add extra options to your code so I went to the development kit for a quick test and debugging...
I cannot get the esb ptx sample to compile on NRF52833 device when using VS Code v1.64.2 running windows 10 64bit .
I've installed everything according to videos, and when...
I am developing a nRF52832 based project where I want to position people indoor using an smartband (where the nRF52832 is placed). I was planning to use beacons so I can change...
Hello,
I have a ported a project from Keil (uVision) to Segger Embedded Studio. Everything is compiling, but unfortunately I have a problem with the linker I cannot solve...
Hello,
I am looking for some advices for a personnal project.
I would like to be able to receive all BLE packets ( so all protocols (GATT, SM, LL) and not only GATT) that...
Hi Nordic team,
I have used the nRF5340 BLE Online Power Profiler extensively in the past for things like estimated event energy and estimated battery life. Do you have...
Hello,
I use the nRF52840DK with direct programmed registers for NRF_RADIO peripheral to send and receive 802.15.4 frames. I have also a separate laptop with nRF52840 USB...
Dear all,
We're developing a custom HW with several nRF52832 chips on one board. For convenience we applied third party module instead of building minimum system by ourselves...
Hello,
in our device we use the Timeslot API to share a 802.15.4 based protocol with BLE, softdevice is S140 6.1.1.
Problem: the 802.15.4 protocol misses appr 10% of the...
