Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I have a central-peripheral FW over a nRF52840-DK running NUS service and I have to measure the throughput between the nRF52840-DK acting as a peripheral of a mobile...
Hi
How do pass bat_num into the declaration for the power config attribute list? Perhaps I overlooked it, but it wasn't evident to me when reviewing the Developing with...
Dear ,
I am going to use debug out function on RF5340 DK.
connection is as below: customer board conncet to nRF5340DK.
customer board use nRF52833.
I tried many times...
Hello All,
First, thanks for this post: https://devzone.nordicsemi.com/f/nordic-q-a/40924/how-can-i-restore-the-original-bootloader-of-a-pca10059 ; I'm attaching the file...
Hi. In nrf52840 is it possible to use in NRF_LOG the second UART (DMA based) ?
I know i can define the TX pin in the SDK_CONFIG but can the NRF_LOG_BACKEND_UART work with...
Hello I am trying to get the usb cdc acm module to work for the nRF52840 dongle. However, the example is made for the dev kit. I flashed the dongle with the example anyways...
Hello,
We are looking at using an nRF52 Series microcontroller for a BLE device. We are trying to decide if we should use the nRF5 SDK (which we have used in the past) or...
Hi Nordic team
1. Define one vendor client model and one vendor server model at mesh nodes.
2. Provision all mesh nodes. Then, Create a mesh group 0xC000.
3. Configure...
Hi - Recently, the NRF Connect Toolchain manager stopped being able to open VS Code and hangs spinning - screenshot below. It used to work so I'm not sure what's changed....
We want to verify that the modem can find mobile networks without actually connecting. Actually connecting to the network has a price tag. The context here is a quality assurance...
Hello, Support
I am new to Nordic and try to follow the tutorial video here https://www.nordicsemi.com/Products/Development-tools/nRF-Connect-for-VS-Code/Tutorials
Just...
Hello all,
The sensor (VCNL4035) is connected and found by the nrf52dk. Indeed, the twi_sensor/scanner have been quickly recoded and it shows some progress...
The manufacturer...
Hello,
I am using ble_app_uart example in sdk 15.2 and nrf52832.
I am using this example to communicate with other MCU. It is continuous Rx Tx between nrf52832 and other...
Hello,
I am currently implementing a security protocol from the IETF LAKE working group called EDHOC in Rust. I am using nRF5340dk and the bare-metal Rust examples from...
Hi there,
I am currently following this following tutorial on building a Matter setup.
When trying to build the openthread coprocessor I am hit with the following error...
