Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I am using nrfconnect sdk with central_uart example. How to get the name of the device
advertise the BLE discovery packets? nrfconnect android app shows the name after...
Hej!
I see that the CRC block is used in the Radio under section 23.6 of nRF52832_PS_v1.4.pdf . Also, I noticed that the CRC32_ENABLED is only enabled in the bootloader...
I'm using the UDP sample from SDK 1.8.0 with the following modifications:
No PSM
No eDRX
Send 100 bytes every 15 seconds
This is on the nrf9160-DK board.
I suspect...
My previous ticket is closed. I would need, but still help with the configuration of the pins. I report my last post.
Hello, I did some tests with the oscilloscope directly...
Hi,
The previous SDK would allow configuring radio notifications before the radio comms would take place.
I wonder if it is possible to get similar notifications on the...
i have a requirement to connect two nrf52833 boards to connect each other.
(1).if i turn on the Board1 should scan the bluetooth devices if any other bluetooth devices present...
I am working on a proprietary RADIO protocol on the nRF5340 device. Because I'm trying to squeeze as much throughput as possible out of the RADIO I would like to be able to...
I am developing my first BLE Server application with the nRF52832 and using VSC/nRF Connect/Zephyr ROTS. I come from a Cypress/PSOC Creator background, and am struggling a...
Hi DevZone,
I recently updated my version of SEGGER Embedded Studio for ARM to v6.20. Now, warnings that were not shown before are caught.
I want to ignore the warning...
Hi Nordic, Currently my project is using SDK 15.3. By taking a look at NCS SDK, I can see lots of features there and plan to migrate my project to NCS 1.9.0. However, since...
The NRF5340 net core crashes in sdc_hci_cmd_le_set_adv_enable() if I have CONFIG_CLOCK_CONTROL_NRF_CALIBRATION_MAX_SKIP set to 0.
To reproduce the issue, do the following...
Hi ,
I am using nrf52833dvk and nrf52832 boards, am working on application that my nrf52833 board do the firmware updation of other board i.e. nrf52832 . first time i did...
We plan to incorporate the nRF9160 into many thousands of our devices, however this leads to a question of procuring SIM cards. We purchased a Thingy91 to test the connectivity...
The iBASIS sim card came with Thingy:91 does not work. Got the replacement card today. However, I cannot finish the nRF cloud reg process. The new error message said
Tenant...
Hello, I am trying to load a sample project in VS Code using the nRF Connect SDK extension.
I try to load a sample project, click on "Create Application", and nothing...
