Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I’m currently experiencing some periodic MCU resets while testing the BLE Multiple central single peripheral scenario, whose root cause is not clear to me, except that...
Excuse me:
I want to achieve t he maximum transfer speed between ble_app_uart and IOS NRF connect app，How to modify the example to achieve the maximum transfer speed with...
Hi
We are now using SDK v17.0.0 for our product and planning to upgrade SDK v17.0.2 because SDK v17.0.0 could no longer be downloaded.
But SoftDevice for each SDK is...
Hi all,
Background: -NRF5340 -NRF SDK 1.9 -Zephyr 2.7.99 My objective is to send via Bluetooth data of 244 Bytes every 10 ms per notify . For the tests, I use the dongle...
Hello,
I'm quite loss using the command nrfjprog.
I install in VSCode all NRF tools. It seems working good. I can compile.
When I have a look on "device tree" I cannot...
Hello,
We want to read external sensor data using uart in lwm2m_client project.
I tried below following code :
static char RX_Data; static char uart_buf[20]; static...
Hi,
I could see that in nCS path : "v1.8.0\mbedtls" , "mbedtls" library is provided, I need to understand what it does & how do I enable it for use in my applications...
I am attempting to build and run the Zephyr NVS sample ( https://docs.zephyrproject.org/latest/samples/subsys/nvs/README.html ) on the 52840 using the nRF connect extension...
I have an Adafruit nRF52832 board, and I'm trying to minimize power consumption by putting it in system off mode. It is attached to a breadboard, and none of the pins are...
Hi Nordic Team,
I noticed a potential issue while migrating from SLM v1.4.0 to v1.9.0. In addition to the inversion of the <state> representation in #XHTTPCRSP introduced...
I have developed a Zigbee application using the nrf52840 DK board + nRF Connect + Zephyr and it is working. Now I am trying to move that app over to the nrf52840 dongle. It...
Hi, I am using nRF52832 development board and I have a motor driver. Motor driver has external power supply, I am just using nRF52832 to set directions which consumes low...
Hello, I am trying to use the dfu library to update the nrf52840 with a firmware stored in a littlefs file in an external qspi flash. I can successfully read the entire firmware...
