Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
hi,
In my application, which was based on nRF_SDK_Thread, to check my node's connection with the Border router, or to know whether the border router is present or not...
I'm looking to build a custom bootloader for my NRF52810 device. I'm developing on nrf sdk 17 with SD 112. I will be leveraging the secure bootloader example and re-using...
Hi;
i am using sdk 17.0.2 and mesh 5.0.0.
i am using light switch instance.In addition, the system works properly when provisioning is made with a smartphone.
I want...
I am using VSCode and the NRF Connect SDK
I can build and flash my device however i keep getting cannot open source file for all my includes, i also cannot navigate to...
First, NRF52833 work environment at 100 degrees celsius, standby current reaches 60uA.
Second, When the NRF52833 working in 100 degrees Celsius, what kind of processing...
I have a secure BLE DFU project that is basically a duplicate of the example project (secure bootloader pca10040_s132_ble). I am able to flash a merged hex on my custom board...
I generate the hex file for a release and then tried to rebuild it in a different folder. This is to ensure that all the required files are checked into the archive system...
Hi,
We are developing a firmware using the nRF52 DevKit as a reference, as well as its companion iOS Application.
Pairing & Bonding:
We have successfully integrated...
Hello !
I have evaluated AES-CCM co-processor in on-fly and from memory-to-memory encryption/decryption operations and see it works in BLE 2Mbit mode without visible problems...
I can not seem to figure out why when I init the advertising and then issue a start to the advertising the advertising beacon shows up as a connectable when viewing under...
Hello,
I am using SEGGER Embedded Stuido for ARM(Nordic Edition) V5.68 for NRF9160 evaluation.
It was Okay for while. But, suddenly, I met error message(SyntaxError...
Hello,
We are using nRF sniffers in CI environment for troubleshooting Bluetooth LE related problems. Since we are adding more and more sniffers, it would be really helpful...
Hi!
I am trying to enable a UART line for a peripheral that I want to interface with on a nRF9160. I am trying to set it up as an async or interrupt driven interface as...
I'm working on a 52840 board controller project that requires serial communication with the 9160 (on a nRF9160DK board) and BLE communications to an Android tablet. I have...
I am in the situation that I have 1000+ deployed devices with a buggy bootloader in a production environment. The current application version triggers this bug, which means...
