Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
My hardware guy asked me to look into whether or not we can use a fixed eSim (no card) with the 9160? If this is possible how do we program it with the particular...
Hi,
GOAL : I try to measure the current consumption in system off only.
PROBLEM : I measure a current of 8uA in system off while in the datasheet of the PAN1781 et nrf52820...
Hi, I accidentally marked one of my own replies as the answer.
I'm trying to interface LR1110 (Dev Board) with NRF9160 DK using SPI. I have been working on this for a couple...
Hello,
I am looking for an example that have the the ccs811 on the sdk15 but i didnt find it , I have found some driver ext like ccs811.h on the driver_ext file but I dont...
Working on a zephyr/zigbee/802.15.4 system and my code (loosely based on the Nordic samples) on a custom device was not behaving as expected.
So I broke out an nRF5340 DK...
Hello Devzone,
I'm writing to ask about how long a device running Nordic's aws_iot sample app (sdk-nrf 1.6.1 based, Zephyr 2.6.0 based) may be in a "radio idle" state, and...
I'm using an application based on the MQTT_CLIENT example. Without any change, it worked fine.
Now I tried to add UART2 as a communication channel to another controller...
Hi Community,
I am using ble_hrs_heart_rate_measurement_send API to send notifications to my central device which is a android mobile.
Recently I have observed packet...
Hi,
I am writing an app for nRF52840 with sdk 17.0.2 and freeRTOS.
The device should be a peripheral which a android app should be able to connect to.
Everthing works...
Hi,
How are you?
Could help someone with a ask?
I am designing a plate and I am using like guia the nRF9160 DK. The Layer Stack Manager has configured the Top Layer...
path:
\experimental\cli\cli_agent_router\pca10059\mbr
When I execute "bdb start" in the serial port and then execute "bdb Legacy Enable", the terminal devices that are...
Hi Nordic Team,
My dev enviroment is as follow:
nRF52832(ble central)+ S132+ SES+ SDK 17.0
We are facing an issue regarding local BLE Address . When we are flashing...
Hello.
I am developing a peripheral roll using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I want to know the information of the device that sent the connection request. Also...
Dear Nordic Team Support,
I am testing throughput on different environments, my goal is to stream data from custom-board to Laptop. I have set up some experiments as shown...
