Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
1: The Apple's "Find my function" , How big is the "Find my SDK" ,RAM? ROM?
We can use nrf52820, or nrf52811,or nrf52810 to develop?
We must use nrf52832 to develop Apple...
Hi Nordic Magicians,
I have a couple of general questions when it comes to sending large amounts of data (FAST). Ultimately, I'm looking to transmit data with a throughput...
Hi,
I'm putting together some firmware that takes packets received over SPI and then streams them over BLE. I'm trying to run the BLE at close to 1Mb/s (which is still...
Background:
Custom boards
SDK 15.2.0
SoftDevice: s140_nrf52_6.1.0
Please see previous post / case that was closed and cannot be reopened: https://devzone.nordicsemi...
Hello,
I am using zephyr on a nRF52840 to communicate with a vl53l5cx TOF sensor using I2C. When I use i2c_reg_read_byte() or i2c_burst_read(), the device address is sent...
Does anyone know why I am getting low outliers on battery measurements with the SAADC? I am measuring the battery directly every minute. Every seven minutes consistently,...
HI,
To ensure NRF5340 2.4G rf consistency during mass production, which scheme do you suggest is more suitable （ X2 = 32MHZ 10ppm ）:
1、Offset capacitance C36 C37 placed...
I used Modem firmware version 1.3.1
In order to connect the nrf9160 DK to the AWS cloud, I am encountering errors such as AWS_ IOT_ EVT _CONNECTING, when it should be AWS_...
In a nrf52840 project using Zephyr 3.0 following Zephyr drivers are used:
the modbus serial driver(RTU mode) which uses uart1 in interrupt mode
the lora-mac driver which...
Hi,
I'm using app_ble_uart example using nrf52810 for nrf52810 UART RX & TX pins are (P0.15 - P0.14) while configuring using i got a problem with RX transmission ,when i...
Hi,
I am working on a multiple custom models, wherein I need one model to extend the functionality of another model.
I was analyzing through nCS provided "Chat" sample...
We have relatively big model composition, and reading it via nRF Mesh app fails if it exceeds 21 segment message.
However the limit I assume should be at 32 segments and...
Hello,
I'm running nRF Connect SDK v1.9.0 on two nRF52840-DK devices, one Peripheral other Central.
My application requires to initiate pairing, i.e. send pair request...
Hello,
I'm trying to set up nRF Connect for VS Code. I followed this video for installation steps: https://youtu.be/2cv_jjqk5hg, the only difference being that my nRF Connect...
Hi, I'm running the sample "peripheral_uart" on an nRF52dk. It has a config called CONFIG_BT_NUS_UART_RX_WAIT_TIME, which is set to 50. The comment says the unit is milliseconds...
