Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi,
I enable the watchdog in the application image, then call soft reset to enter the bootloader, the bootloader execution is also normal, until the watchdog is reset. ...
Hello!
I have a situation where a chip is connected with an antenna on a u.FL slot, what I want to do is to remove that antenna from the chip and connect my nrf52840 to...
Hi,
I want to send the I2S MIC Raw data through Ble by using ble_nus_send. I have written one application but it triggers a Cmake error. I have attached the log below...
HI I'm using the nrf5340dk, and I'm able to flash the application core with code that toggles the LEDs.
But I'm not able to flash the network core. I've specified in the...
Hi, I'm currently designing a system which requires Heart Rate monitorization and I'm using the MAX30101 chip to do so. I will be using I2C communication and, therefore, based...
1. We use code similar to the existing sample code to repeatedly sample a 0 - 2.25V voltage range using the SAADC. 2. Settings: 30s interval, single-ended input, burst-mode...
Hi All,
I'm looking for a PC based tool with similar functions as nRF connect. Our manufacturer is developing a functional test fixture which will PC based and will be...
Hello,
I'm looking for reading the sent data from an old embedded autonomous nRF905 (which act like an active tag) and I thought I could use this convenient-looking USB...
Hi,
I am using nrf52810 with custom board and i want to create OTA file for custom application. while compiling the bootloader to get hex files, i am getting error as "Target...
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
from the datasheet we see that this device can operate at 1.8V or 3V3 (or anything in between).
We can also check supply current on the mRF52DK which runs at 3V3.
How...
Hi everyone,
I would like to measure the total current consumption of the board in order to get an estimation of the battery life. I am using PPK-2 and nRF Connect Power...
Hello Everyone,
For my project, I have to make my BLE device to advertise itself for a period of time and transit to "scan" mode to scan for other device for a period of...
I am getting this fault when i try to run a observer handler where i have implemented semaphores.
And i cant figure out what this error code means
Thanks in advan...
Hello,
I am currently trying to run this ble_secure_bootloader . I am using SES V5.68 with the nRF52840 SoC and I am using nRF5 SDK version 14.2.0. I have also adjusted...
