I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello, I recently picked up a nRF PPK2 and I'm liking it a lot.
I have it wired in-line with a battery (1500mAh li-po) with my device under under test. Measuring battery...
Hi,
I am using nRF52805 to transmit string data to the mobile end app "nRF Connect".
I found that sometimes the app will display hex data instead of the expected decimal...
I'm using the logger (LOG_INF, LOG)_DBG...etc) to print out debug messages. I'd like to have timestamp printed out. Right now it looks like this: D: xxxx or I: xxxxx
I found...
Hello, I am working with 2 nRF52840 dk's and a Conbee ii.
The DK's are using nRF5 SDK for Thread and Zigbee 4.1.0.
DK 1 is running the CLI example.
DK 2 is running...
Hi, I want to integrate DWM3000 with with nrf9160. To begin with, I need a simple SPI example which I can't seem to find in the nRF connect SDK. There is an unofficial example...
I am using P822601 board (with nRF9160 chip). Sample project "Serial lte modem" (SDK 1.8). I'm trying to connect to a test mqtt broker (mosquitto) using AT commands via LTE...
Hi,
We have to enable the radio shorts in our developing multi link firmware. ( We let any node connect to 3 other nodes at the max ( 1 as a slave and 2 as a master )) ...
Hello,
I successfully merge example libuarte and ble_app_beacon and built .
My problem started after it receive 48 bytes of data from sensor via uart ,This is my area...
I want to enable GPIO IRQ in Trusted firmware-m 1.3 on nrf5340DK. I have TFM 1.3 which comes with zephyr v2.7.0 image flashed to board. followed the steps of https://www.trustedfirmware...
Hello,
I am trying to protect the battery on our application by putting my device in DEEP_SLEEP_! mode when a certain voltage is reached and waking it up upon a GPIO input...
Hello, i would like to know if this is possible to send less than 20bytes per packets, by changing the parameters like BLE_GATT_ATT_MTU_DEFAULT or the max data len. My goal...
Hello,
I'm trying to evaluate the Thingy:91 on Nb-IoT networks. I'm currently in the Philadelphia suburbs. I'm using the iBasis SIM card which was packaged with the device...
We like to use nrf9160 and we tried to find operator in India who sells NB-IoT / LTE-M sim card. but unable to find. Is there any operator providing NB-IoT / LTE-M enabled...
Dear Forum,
Im using a NRF52840dk connected to a NRF9160dk with the SLM application running.
Sending uart data from the 52840 to the modem works and modem gives a response...
