Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi.
Setup:
I use NRF5340. Open project from SES menu "Open nRF Connect SDK project".
nRF Connect SDK Release: 1.4.99-dev1. nRF Connect Toolchain Version: 1.4.0.
Project...
Hello! I tested the ST BLE Sensor sample on my nrf52840 DK. I have a few questions about the source code: 1. Looking at recv(), connected() and disconnected() functions, seems...
All nRF5340 reference designs use via-in-pad structure. Instead e.g. nRF52840 has reference designs which can be used with through hole PCB.
nRF5340 seem to have 19 IO's...
Hi,
I'm trying to do a very simple thing - setting those pins as high or low,
but I see that it simply does not work for those pins, I see no change in led state that...
Hi everyone,
I'm developing on nrf9160DK. I would like to know if there is any difference between setting the APN through the CONFIG_PDN_DEFAULT_APN in prj.conf file or...
I am using the SLM app from the 1.9.1 SDK.
I connect to my MQTT broker using TLS offloaded on the modem. I subscribe to a topic using QoS = 1 Then if a message is published...
I have been trying to get mqtt to stay connected without activity for more than 30 minutes. any keepalive value over 30 minutes just results in mqtt discoonection. tried with...
On a custom board, I've got 2 inputs connected to an external pullup and a pad. One in is P12, one on P21.
When I short the pad for P12 with GND, that input read low, that...
Hi,
I tried to access Nordic devzone, yesterday and today, but got an error message that "the page cannot be displayed because of an internal server error has occurred...
Hello everyone!
I am trying to figure out how SPI drivers for Bosch bme280 sensor work... I would like to somehow recycle them to write my own SPI drivers for another device...
Hi Nordic,
Using nrf-connect 1.9.99 and Zephyr 2.7.99 (*** Booting Zephyr OS build v2.7.99-ncs1-1 ***)
I am using then nRF9160-DK and everything is fine. Getting 40uA...
I'm running Manjaro Linux and have ran through the installation instructions for the nRF Connect Desktop. I have separately downloaded the Segger JLink software as instructed...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
Hello, I am using 52832. There is an external interrupt count with a maximum frequency of 1kHz. I have two hardware. One I transmit to the mobile phone at an interval of 50ms...
Hello sir ,
i am trying to build file from given sample code file name is "azure_iot_hub" , i don't make any changes in this file .
on adding build configuration it show...
