Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to implement WDT and expecting to occur its event when the module becomes...
With the release of the Bluetooth 5.2 standard, also came the introduction of BLE Audio.
Since I am evaluating a SoC for bluetooth headphones, I stumbled upon the fact that...
I have an nrf9160dk setup with the bluetooth-hci-lpuart flashed to the nrf52 chip and a bt peripheral sample flashed to the nrf91. This works as expected. However, I am trying...
Hi Everyone,
We are currently stumped and are looking for guidance. A brief overview of what's needed from our client are as follows:
1) From the nRF mesh app, send...
Hi,
im using sdk 17.1 with segger embedded studio v6.2a and nrf52840. I am trying to use the uart example and it gives an error no name type found "__printf_tag_ptr". I...
I encountered a problem in configuring the general switch model. I want to configure the group address at the beginning. I set the dsm_address_publish_add（） and access_model_publish_address_set...
When I was adding the ID of the sensor, I found that the specific name displayed on the Bluetooth app is not my own name. Is there a special definition for this ID? I checked...
Hi
I'm looking for a clear statement about to do or not do modem firmware downgrades on production devices.
I know that
nrfxlib does not mention anything about modem...
Hey, I'm working on a real-time body motion capture project and using nRF52832 as BLE MCU. In the system I have 3 IMU sensors to transmit sensor data to an Android device...
Hi,
This is a repeat of case 279137 but I see no answer to that so here goes again...
I am building sample Zephyr applications in VS Code. Everything was working fine...
Hi!
We would like to be able to send two separate dfu-packages independently, one hex/pack containing our main application and one hex/pack containing data to be read by...
HI All,
We are using NRF52832 for our project.
1) We are using System ON mode to put NRF52832 in to sleep mode. We are able to put NRF52832 in to sleep mode(System ON...
Hi,
I am working with the nRF52832 DK. I want to program a couple of ICs with SPI every 2 ms. I have successfully configured the nRF as SPI master and I start the SPI transfers...
Hi All,
I wanted to look at the power profile for my nRF52840 dongle, I installed nRF connect and installed the Power Profiler. But as I want to the option to connect the...
