Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi, I need to add Azure IOT connectivity to nRF5340DK. I have already tested NodeMCU based data upload to HTTP based server and successfully working. Now, to divert the data...
I am trying to upgrade SoftDevice and Application firmware from v6.1.1 to v7.2.0 on Nordic USB840M dongle and I am facing a strange issue after such upgrade.
Please find...
Hi,
I have created my own service and charecteristic
1. But i am seeing only unknown service - How to give a name to this service
2. I am getting unknown charecteristic...
Hi
I have compiled (successfully) the Zephyr example samples/bluetooth/peripheral example for the nRF52 DK (nRF52832).
I am going through the code and trying to understand...
Hi
I have developed a device using the nRF52832 and I am wondering if there is built in functionality to reset the chip back into bootloader mode without programming the...
Hi All,
I'm using SDK17.1.0 and I have a question about mobile device subscribe.
I asked this question before, but the engineer didn't reply, so I asked again, thank...
Hi All,
I want to port BPS to my custom project, I encountered the problem as the title.
When I connect and trigger the subscribe like this picture.
My project will...
I have code that runs for around 5 days, then for some unknown reason hangs or stops running, which makes it almost impossible to debug.
I have also tried to implement interrupt...
Hi.
I have an issue that, If I power off Master and do save flash at Slave side together, the nrf_fstorage_is_busy(p_fs) return value always true .
When BLE is connectting...
I added a mesh shell module to my firmware running on nRF52480 .
Opened the mesh shell
uart:~$ mesh init Mesh shell initialized
mesh provision 0 0x100 0
Crash (see...
I've been slowly adding NVS functionality to my code. Has been working fine, up until today when I attempted to write a struct I have for storing historical data to flash...
Hey,
I have implemented BT FOTA process for my zephyr based application. DFU over Bluetooth works fine. But now I struggle to implement manual upload of image (it will be...
Hello Devzone,
My name is Ted. Recently I posted here and received some good help on low power sample code for the nRF9160DK board. This code helped me prove in real life...
I'm currently trying to set up a simple demo using 2 dev kits running the SPIS and NRFx_SPIM examples but the SPIS seems to always send corrupted data over the MISO line....
Hi,
I'm using two dev kits to test out some SPI firmware before I deploy it to our custom boards and I've been running into a weird issue where my SPIS sends out corrupted...
