I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello!
I need to control several motors using the nRF52832. The problem is that my laptop cannot supply enought current to run the motors, if I try to run it, windows detects...
Hello!
I am trying to write a program for controlling a servo motor. I got recommended a code for making a PWM signal by someone else from devzone, so I am using a modified...
Hello, I would like to know what is required of me to automatically create com port in windows that would allow me to use my ble device as if it were attached by ordinary...
Hi,
I want to receive some data in my nRF52832 from MATLAB over UART and send some other data from nRF52832 back to MATLAB. I need some bandwidth for data transfer from...
Dear support,
I am the beginner of of the Nordic with 52840 chipset, i am try to running sdk 1.90 with zephyr os
i am try to running this case : cfb
C:\Nordic\NCS...
Hi,
I'm trying to use two nRF52840DK as Zigbee routers. I have the following setup,
Software
Application: Home Assistant
SDK: nRF5 SDK for Thread and Zigbee v4.1...
I really like the flexibility that the CLI from FreeRTOS gives me for making my own commands. Does Nordic have a similar library available that I can just import easily into...
Hi,
since The image management provided by mcumgr is based on the image format defined by MCUboot, so does "nRF Connect android app DFU mode" use mcumgr libraries in it...
I'm developing an Ultra-Wide-Band indoor localization system consisting of beacons (stationary, hard powered) and tags (mobile, battery powered), and am looking for a suitable...
Hi Nordic,
I am developling a porject with nRF5 SDK 17.1.0, with nRF52832.
the 52832 serve as a central role.
1、I am wondering what is the difference between BLE_GAP_EVT_CONNECTED...
Values change rapidly and bt_gatt_notify_uuid is called at 10ms interval while bluetooth connection is set up for 15ms connection interval. I assumed this would simply queue...
I have attached all sleep modes of our controller that i found through forums and from your suggestions.
But my problem is No one of these sleep modes, wake-up through...
Hi,
I am just starting out creating a project to run on an nRF9160 on custom hardware. I have set up a development environment (v1.9.0) through nRF Connect for Desktop...
Hello I use nrf52840 and BME280. I plugged it GND GND SDA 45 (P1.13) SCL 47 (P1.15) VCC 32 (P1.00) I use timer to refresh data and on the first line of the code I init gpio...
Hi,
In the nRF52840 Product Specification 1.7 , page 34 chapter 4.4.1.9 INFO.VARIANT, I read that the hex code of variant "AAF0" is 0x4141 45 30. However the description...
