I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi Nordic，
I am using nrf52840 custom board. May I ask, can I replace 4.7uf near VDDH and VBUS pins to a larger cap, like 10uF? As far as I can see, these caps are only...
I installed the nRF Connect extension pack which also contains the nRF Terminal extension but I cannot make it work in VS Code
In the command pallette I select nRF Terminal...
I wrote some code to read the Adafruit PDM Microphone Breakout board sensor output (ST MP34DT01-M microphone) with Zephyr and nRF Connect SDK into the Thingy 91.
I do this...
Hello
Im trying to use my iPhone 13 with your application nRF Connect as a peripheral.
For some reason the moment I make a connection with another device it automatically...
Hello,
I am using the Adafruit Feather nRF52 Bluefruit LE - nRF52832 for a project where I will have to transmit and receive data over Bluetooth Low Energy between two of...
Hi,
I have a nrf5340 SPIS peripheral being driven by an STM32H753 micro. Data transfer works fine except when I connect a scope probe to the CSN pin. With the scope probe...
Hi,
I have been trying to chase down an issue with the flash manager occasionally raising an assertion in mesh_config_backend_init() after a power cycle of the nRF52840...
Hi everyone,
I have this problem with the firmware protection method in nRF52833. As far as I know, when using secure boot-loader, it can prevent other programmers to flash...
Hi everybody,
I want to modify the Tx characteristic on Nus service to Indicate.
Keeping if is possible Rx characteristic as notification.
Are there some tutorial or...
Hello, support
I use nRF52833 SoC and need to host it with external NXP MCU to control its function, interface is 3 pins only, I wonder whether there is any example code...
Hi all,
I'm trying to debug my nrf52480 with vs code.
I followed the nRF Connect for VS Code tutorials: Add an existing application, add build configuration and than...
Hi Guys,
I want to have some BT-SIG RF PHY tests on nRF5340 DK with R&S CMW270.
I can perform direct test mode in nRF Connect for Desktop,
but I cannot connect nRF5340...
Hi, I am developing my own application based on the newest demo direction _finding_connectionless_tx and direction_finding_connectionless_rx with Dev board nrf52833.
I am...
Dear Nordic Engineers
I used NRF CONNECT SDK on NRF52840,I have some questions,Please help me.
1、I used the buttons module of the Common Application Framework ,but I found...
Hi Nordic:
We are working on a project, using NRF52832, which has the functions of softdevice+bootloader+ble+dfu, the SDK we use is version 17.0.0,
and RTC2 is used as...
