I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi there,
I am trying to enable the Read Back Protection in the software itself to avoid the FLASH, RAM etc. from being read with a debugger after being flashed for production...
Hello, I'd like to check what is the typical distance using 0 dBm tx power using Nrf52840?
I am using this BLE module based on Nordic, and it seems to work ONLY 2-3m far...
Hello
I am getting started with Nordic devices.
I recently bought a Thingy:91 and followed a tutorial to load the Asset Tracker application on to the device – this...
Dear,
We have been using QSPI external flash (MX25R64 installed at nrf5340 DK board) to write data. Particularly, when we ran flash_area_erase function ( located at zephyr...
Hello All,
How can I get my nRF52840's MAC address in Zephyr? Actually, I want to append the last 4 characters of the MAC address in CONFIG_BT_DEVICE_NAME.
So, when I...
Hello, we are developing a zephyr application on top of nrf52 soc. We can use the built-in zephyr drivers for most modules (ex: I2C, UART, nvm, etc.); however, for some modules...
I am really new at working with Bluetooth and the various protocols contained within.
I am using SDK 17.0 and drivers 2.7. I am working on a DK-52 board.
I am working...
The TWIM peripheral allows you to tx multiple buffers back-to-back like this:
- Set buffer 1 in TXD.PTR, TXD.AMOUNT - Trigger TASKS_STARTTX - Wait for EVENTS_TXSTARTED ...
Hi,
For testing purposes, I need a copy of the spec that the Nordic UART BLE service adheres to. Ex. minimum capabilities, mandatory functionality and attributes, etc. ...
Hello,
I tried enabling the Zigbee shell, through RTT, in my application and when that failed I built and burned the nrf/samples/zigbee instead, slightly modded to get rid...
Hi All. My task is simple. I want to implement LE secure connections on DFU. I have seen the ble_gls example. It has a passkey for bonding, I am looking into that too. I ran...
I have a repository that is intended to be used by other repositories via ZEPHYR_EXTRA_MODULES. This seems to be working fine. However, now I'm trying to add some code to...
I am evaluating a front end module by skyworks 66111 output power is ~14dBm. The FEM requires that logic dictate when to transmit and when to receive. When CRX, pin 17, is...
HI
we have developed our custom board using nrf5340. We are using NCS v1.7.1 for application development. I can't able to flash the HCI_rpmsg application to the network...
