I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hi,
I build the smp_svr sample for nrf52dk_nrf52832. I installed Go on my windows machine and I am able to run the mcumgr tool. When connecting Teraterm to the UART of my...
Even if i did the configurations i got this error because of the manifesting stage.
When i did the configurations which is like below,
west config manifest.group-filter...
Hello,
I am trying to use Direct Test Mode example on SDK v17.0.1 to do our product's pre-production RF tests. I can see expected results on nRF Connect Direct Test Mode...
Hi, While testing the new nrf5340 Audio DK and BIS example, I wanted to see how the Periodic Advertising Sync Transfer (PAST) data looks on the nRF Sniffer version 4.1.0....
Hello,
I want to know to which pin should i rely my AMPERMETER so i can measure the current consumption of the µC .
If you have other hardware solution to measure the...
Hello,
I am trying to flash a Sparkfun thing plus nrf9160 board but I am not able to for some reason.
This is what I am getting on the logs when trying to select the...
Hi all! I'm new to mesh bluetooth technology and I'm stuck with some bugs.
I am using the development boards nrf52dk and my goal is to create a network of about 6 nodes...
I am using nRF5 SDK version 17.1.0 and am seeing this line in file examples/ble_peripheral/ble_app_uart/pca10040/s132/ses/flash_placement.xml
<ProgramSection alignment=...
Hi, I am trying to transmit data via Bluetooth from two sensors at the same time to a dongle that will send the data to the computer via USB, I am able to connect the two...
Hello,
I'm doing some current measurements on both the Thingy91 and the nRF9160DK and I'm seeing some weird behaviours. My setup is as follows:
First measure on the nRF9160DK...
Hi dear reader
I've read several threads on this issue, but none of them could help resolve my problem.
I've an application which currently is only starting some advertising...
Hi
I am looking for an advise about selection of the optimal connection parameters. I am using couple of nrf52832 devices as the nus peripherial. As the central device I...
Dear colleagues,
I'd be very grateful for your help in the following challenge: I would need to change pins and/or i2c bus speed without recompilation of my code.
I can...
Hi,
I am following the NRF5 getting started guide. Unfotunately, I am falling down at the first hurdle. When copying the .hex to the JLINK storage, a fail.txt is generated...
