I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi all,
struct spi_config {
uint32_t frequency ;
uint16_t operation ;
uint16_t slave ;
const struct spi_cs_control * cs ;
};
in documentation, it says...
Hi I am recently working on Enhanced Shock Burst (ESB) protocol. where PTX and PRX
and
PRX will communicate upto 8 PTX
i have a question like how a single device will...
I'm working on porting some Arduino code for a Crystalfontz 320x240 FT810 display to run on the nRF9160DK. I'm having some success, But it seems Zephyr has an FT8XX driver...
I use a example application from SDK_DIR\examples\ble_peripheral\ble_app_template\pca10056 base on nRF5 SDK v17.1.0,then use SDK_DIR\examples\dfu\secure_bootloader\pca10056_s140_ble_debug...
Hello there, my application needs to switch master/slave roles after the connection established.
As i know, the initiating device will be master every time in BLE. From...
Hello.
I am developing nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a characteristic using characteristic_add. I want to set the attribute handle...
Hi
1、 A customer wants to evaluate the keyboard that can run ble and mesh simultaneously with nrf52 chip.
2、I found mesh example in both NCS and nrf5_SDK_for_Mesh_v5.0...
Hi, I am working on this project where provsioner provisions all the unprovisioned devices (nodes) and then sends the LED's data (containing brightness, intensity and pattern...
Hi, I tried running an spi sample program with code as in below, shorted the MOSI and MISO pins and data was visibly received in print statement:
While in the same code...
I have recently bought nRF9160-DK on Mouser, here's the product page: https://www.mouser.ie/ProductDetail/949-NRF9160-DK
On Mouser, it is marked as LTE-M NFC NBIOT GPS &...
In an attempt to do in app DFU I have taken the following resources for inspiration:
nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_uart_debug
and the...
Hallo,
I am looking for some tutorial for developing BLE centre and peripheral device using nRF5340 DK. I am not familiar with SEGGER and device studios so I am working...
Hello,
I have the nrf52840 dongle but as you can't debug the code in the nrf52840 dongle, I want to use the nrf52840 in the nrf9160 dk module.
I'm a beginner in this....
