Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi
I'm on the very beginning stage to ncs for vscode.
I followed the course to build my first blinky example, but failed always.
I double checked my step and all the...
Hi,
I'm using nRF52832 development board with blinky example and with PPK kit I'm trying to get the actual power consumption from the development kit.
I think the actual...
We are working on a project where we have space constraint. We are placing AMS AS7038 , which is a Biosensor Solution with Embedded ECG Channel + Analog front end, just on...
Hi,
1. I tried to test AGPS, but an error was reported. The test results are as follows:
Why is the error reported? Is it that this routine does not support AGPS, or is...
Hi! I was wondering if I could use an SWD connection to recover a bricked chip. This chip is on a custom PCB that has pins allocated for SWD.
The chip itself is stuck at...
I'm looking for assistance or example sources of being able to dynamically control the Nordice device subsystems power. i.e. the serial uart used for the Zephry shell. But...
HI .
Two questions for the nRF52840, please have your comments, thanks. 1. Does nRF52840 Zigbee support SEP 2.0? 2. Can nRF52840 Zigbee be replaced with other protocol?...
Hello ,
I am facing issue while building Building example DFU application 'secure_bootloader_ble_s132_pca10040'
I am using SEGGER Embedded Studio IDE, and while building...
Good afternoon, I am new to nordic sensors. I would like to develop a phone application using Android studio that reads accelerometer values from the Nordic 52. How could...
Hello,
I am using nrf52840 with led blinky example for power consumption but it consumes 0 micro amp so i think reading was not correct so how can i troubleshoot this ....
Hi,
in my application I have setup the nRF52 to wake-up from deep sleep if a low value is detected on either of two GPIOs (4 and 5). What I'm trying to achieve, is to be...
I changed the SDK version of my project according to the steps of How can I change the SDK version of my program - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi...
Setup Visual Studio Code and installed the toolchain manager stuff got 1.9.1 of the SDK and the command line stuff for my windows 10 machine (if that matters). And trying...
Hello,
I have a Nordic Thingy 52, and I installed the Android application from github: https://github.com/NordicSemiconductor/Android-Nordic-Thingy
I can connect the...
Hello,
I am trying to send data via GATT notify at a rate of 60hz. I have created a tx thread that calls bt_gatt_notify in a loop and sleeps for 16ms. However, during profiling...
