Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Dear,
We enabled QSPI DMA Encryption to cipher the external QSPI communication with enabling NRF_QSPI_HAS_DMA_ENC. So, QSPI DMA communication worked well.
However, when...
Hi,
This might be a simple answer, but I am working a BLE app which I started from the zephyr peripheral example provided in the nrf connect sdk. I removed the cts service...
Hi,
I'm upgrading our RCP firmware that runs on a custom nrf52840 dongle. It was using openthread bare metal on an old version (clone of openthread repo and run make -f...
Hi,
I am develop with nRF5340, ncs1.5.1.
I am puzzled how to read the value of an output GPIO.
I saw the function gpio_pin_get_raw and gpio_port_get_raw, the comment...
Dear Team,
We are developing HID remote with BLE audio feature which support windows platform.
In the NRF52 smart remote 3 BLE audio support only for Ubuntu.
My Queries...
Hi team!
We are working nrFready smart remote 3 with windows 10 pro operating system.
When we paired the given remote (with battery operated) with the windows device via...
Hey all,
I am starting a little research on how to use my NRF51 DK to control a relay in order to turn off/on 220v operating devices.
I dont know much about electronics...
I'm currently working with a client who is implementing the nrf9160 into their product. They had a version of PCB made which connects pins 104-127 to ground, even though the...
Hello,
We need a bluetooth BLE module, for UART communication with AT command.
with certificatation EN300328 V2.2.2. Do you know where we can buy them?
If we use the...
we are using nrf52805 after in few devices sometimes BLE is not visible(stopped broadcasting) to the receiver.
Here are the observation on that faulty device:-
1. Device...
Hi Team,
we are working on smart remote 3 implementation using nRF52832 with Windows 10 pro operating system.
we tried to connect this remote with laptop using the...
Hello Devzone,
With an nRF9160 based project and lowest power, lowest current consumption in mind, is there an explicit I/O pin setting to make via Zephyr API for the nRF9160...
Hi
Now I am using NCS1.7.1 for development the nRF52840 chip.I need to use the C standard library(math.h).I set up as follows:
There is no problem when the above macro...
Hi,
I would like to know the functioning of CPFD (I would like to represent the characteristic value as IEEE754 float32) I am not aware of how can I implement this. for...
