Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi，
Hello everyone, I have encountered a problem in the pairing and bonding process of BLE.I use two NRF52832 development boards, one acts as a slave and the other acts...
We use FreeRTOS with nRF SDK driver library. The driver library is working well because it doesn't dynamically allocate any memory. So I can simple take entire memory block...
I'm facing some problems when trying to run my custom board on standard batteries.
The device boots fine but when the LTE modem connects I get a reset.
The nrf9160 is...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
I need high performance data transfer, so I review throughput sample. C:\Users\user\ncs\v1.9.1\nrf\samples\bluetooth\throughput...
We are using nRF9160 (Development Kit), SDK 1.9.1 board with "serial lte modem" firmware. We are trying to get AGPS coordinates (using an external antenna), but for some reason...
In the nrf5340 development process.I compile an app core hex from project A and a net core hex firmware from another project B. what method can I quickly obtain a merged firmware...
Hi,
I'm trying to get the maximum possible throughput from a peripheral device, sending notifications to a central. I compare the throughput between 2 PCA10040 boards...
Hi,
I'm using s140 trying to connect up to 8 devices to windows BLE adapter and BluetoothLEDevice object, I have 2 problems,
1- the maximum throughput with different configurations...
Hi All!
I am using Segger Embedded Studio and nRF5_SDK_v15.0.0 .Available kits for testing are nrf52833DK and rak4630(nrf52840).
We want to test nRF52833 support on long...
Both NRF were programmed thru USB NRF connect for Desktop programmer.
Both NRF are running the same soft properly.
To demonstrate the final look and put the dongle in...
Hello,
In my project i am using nrf52810 with my custom board for pushing data to UART so i have used UART example code for this but UART pins are connected 20 (TX), 25...
Hi
I'm working on a Zigbee network, and I want to have a few End Devices (ZED) connect to a Coordinator (ZC). And it's fine, I got that working by using the zigbee_default_signal_handler...
hi
i develop software with the nrf52dk, success with program it with nrf command line tool.
now i want to program the application on the nrf52 dongle but with no success...
I am trying to use SDK version 17.2.0 to develop a package (Boot Loader + SD + Application) for our product based on the PCA10040e board with an nRF52810 SoC.
I soon realized...
