Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello!
I need to control several motors using the nRF52832. The problem is that my laptop cannot supply enought current to run the motors, if I try to run it, windows detects...
Hello!
I am trying to write a program for controlling a servo motor. I got recommended a code for making a PWM signal by someone else from devzone, so I am using a modified...
Hello, I would like to know what is required of me to automatically create com port in windows that would allow me to use my ble device as if it were attached by ordinary...
Hi,
I want to receive some data in my nRF52832 from MATLAB over UART and send some other data from nRF52832 back to MATLAB. I need some bandwidth for data transfer from...
Dear support,
I am the beginner of of the Nordic with 52840 chipset, i am try to running sdk 1.90 with zephyr os
i am try to running this case : cfb
C:\Nordic\NCS...
Hi,
I'm trying to use two nRF52840DK as Zigbee routers. I have the following setup,
Software
Application: Home Assistant
SDK: nRF5 SDK for Thread and Zigbee v4.1...
I really like the flexibility that the CLI from FreeRTOS gives me for making my own commands. Does Nordic have a similar library available that I can just import easily into...
Hi,
since The image management provided by mcumgr is based on the image format defined by MCUboot, so does "nRF Connect android app DFU mode" use mcumgr libraries in it...
I'm developing an Ultra-Wide-Band indoor localization system consisting of beacons (stationary, hard powered) and tags (mobile, battery powered), and am looking for a suitable...
Hi Nordic,
I am developling a porject with nRF5 SDK 17.1.0, with nRF52832.
the 52832 serve as a central role.
1、I am wondering what is the difference between BLE_GAP_EVT_CONNECTED...
Values change rapidly and bt_gatt_notify_uuid is called at 10ms interval while bluetooth connection is set up for 15ms connection interval. I assumed this would simply queue...
I have attached all sleep modes of our controller that i found through forums and from your suggestions.
But my problem is No one of these sleep modes, wake-up through...
Hi,
I am just starting out creating a project to run on an nRF9160 on custom hardware. I have set up a development environment (v1.9.0) through nRF Connect for Desktop...
Hello I use nrf52840 and BME280. I plugged it GND GND SDA 45 (P1.13) SCL 47 (P1.15) VCC 32 (P1.00) I use timer to refresh data and on the first line of the code I init gpio...
Hi,
In the nRF52840 Product Specification 1.7 , page 34 chapter 4.4.1.9 INFO.VARIANT, I read that the hex code of variant "AAF0" is 0x4141 45 30. However the description...
