Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Dear Nordic Team !
I think I found a bug in the ble_db_discovery module of Nordic SDK 15.3.0, maybe other SDKs are affected too. I am implementing a BLE central device for...
I received my NRF52840-DK board, today, from Digi-key. I followed directions in starting it up - power set to USB, switch to on. When I turn it on, all LEDs flash and pressing...
After a lot of stumbling around (the documentation for the ANT+ examples needs to be improved) I finally got some of the ANT+ examples working on my nRF52 DK board. When programmed...
I have developed below I2C code with an RTC timer event handler to sample data from a sensor every 1s. This format is used mainly to save power.
I can see there is a base...
HI
How can I to send 512 characters over BLE NUS?
I saw in Ble uart example this
I received 247data from BLE NUS
can I to receive 512?
how can I do that?
...
Hi,
We are currently going through the Verizon self certify program, using an adaptation of the asset_tracker_v2 firmware on our device. Verizon said to reach out to Nordic...
Look like a hard coded bug in API generated in build\zephyr\include\generated\syscalls\flash.h ?
-- Found BOARD.dts: zephyr/boards/arm/nrf52840dk_nrf52840/nrf52840dk_nrf52840...
Hello! I have a serial device (RN8209 power meter) which is connected by UART to a nRF52832 with 4800 Baud. I am using SDK17 nrfx UARTE to access it, but I have observed,...
We have a custom board with a uBlox Nina-B1 module. Pin 0.05 is connected to an analog switch (NX3DV2567) which powers a microphone and capacitive switch. When the pin is...
Hi everyone,
I am using nrfConnect 3.9.3, And SDK v1.7.0.
I am working on a project based on uart example.
My question is if there are some way for clean/discard all...
I'm unable to get a cloud response using the XPING command with some IoT sim cards on the nRF9160. I've been working with serial_lte_modem projects on this chipset. I've also...
I cannot find any information on how to update mcuboot over SMP when using the immutable bootloader.
I have my NRF52840 setup with the chained bootloader: b0 -> mcuboot...
Hi,
First of all thank you for your support and suggestions.
As I am planning to use nRF52840 SoC in my design, (Project: BLE based Environmental sensor). The circuit...
Hey. In production we are logging PM error events to try to determine the root cause for some unstable connection that keep showing up. We are seeing with high occurrence...
