Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi Nordic，
I am using nrf52840 custom board. May I ask, can I replace 4.7uf near VDDH and VBUS pins to a larger cap, like 10uF? As far as I can see, these caps are only...
I installed the nRF Connect extension pack which also contains the nRF Terminal extension but I cannot make it work in VS Code
In the command pallette I select nRF Terminal...
I wrote some code to read the Adafruit PDM Microphone Breakout board sensor output (ST MP34DT01-M microphone) with Zephyr and nRF Connect SDK into the Thingy 91.
I do this...
Hello
Im trying to use my iPhone 13 with your application nRF Connect as a peripheral.
For some reason the moment I make a connection with another device it automatically...
Hello,
I am using the Adafruit Feather nRF52 Bluefruit LE - nRF52832 for a project where I will have to transmit and receive data over Bluetooth Low Energy between two of...
Hi,
I have a nrf5340 SPIS peripheral being driven by an STM32H753 micro. Data transfer works fine except when I connect a scope probe to the CSN pin. With the scope probe...
Hi,
I have been trying to chase down an issue with the flash manager occasionally raising an assertion in mesh_config_backend_init() after a power cycle of the nRF52840...
Hi everyone,
I have this problem with the firmware protection method in nRF52833. As far as I know, when using secure boot-loader, it can prevent other programmers to flash...
Hi everybody,
I want to modify the Tx characteristic on Nus service to Indicate.
Keeping if is possible Rx characteristic as notification.
Are there some tutorial or...
Hello, support
I use nRF52833 SoC and need to host it with external NXP MCU to control its function, interface is 3 pins only, I wonder whether there is any example code...
Hi all,
I'm trying to debug my nrf52480 with vs code.
I followed the nRF Connect for VS Code tutorials: Add an existing application, add build configuration and than...
Hi Guys,
I want to have some BT-SIG RF PHY tests on nRF5340 DK with R&S CMW270.
I can perform direct test mode in nRF Connect for Desktop,
but I cannot connect nRF5340...
Hi, I am developing my own application based on the newest demo direction _finding_connectionless_tx and direction_finding_connectionless_rx with Dev board nrf52833.
I am...
Dear Nordic Engineers
I used NRF CONNECT SDK on NRF52840,I have some questions,Please help me.
1、I used the buttons module of the Common Application Framework ,but I found...
Hi Nordic:
We are working on a project, using NRF52832, which has the functions of softdevice+bootloader+ble+dfu, the SDK we use is version 17.0.0,
and RTC2 is used as...
