Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
Our customer needs CAT-M, CAT-NB, GPS RF test data
I see that devZone has less information about CAT-M, CAT-NB and GPS RF performance tests
1. Please provide GPS...
As requested I am posting a public question based on Nordic's request here:
https://www.linkedin.com/feed/update/urn%3Ali%3Aactivity%3A6911310498537869312/?commentUrn=urn...
Hi,
parameters A NRF_SDH_CLOCK_LF_RC_CTIV
parameters B NRF_SDH_CLOCK_LF_RC_TEMP_CTIV
1. The internal RC parameter should be configured as follows, but how are parameters...
If AT+CFUN=1 will not get modem connected/registered to a network, what retry algorithm does the nRF9160 implement? Is it something like exponential back-off algorithm?
I'm attempting to add NVS functionality to my code. Had a play around with the zephyr/samples/subsys/nvs example. It was working originally, and then when I started porting...
Hi!
For a project I need to sample an I2C sensor for a period of 1 min with 1 sec between samples with a nordic nrf52832. During this 1 min, a co-processor communicates...
I'm trying to build a custom board in VS Code to use with the nRF9160. I'm using a Thingy91, so I took the board file for that, and copied it into the project directory. ...
I need to test the SPI communication in my nRF9160DK. I had tried to run the spi_loopback but failed to create a project in segger studio. Are there any SPI tests available...
So I have taken a starting point of adding multiple characteristics in the same service using this tutorial:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth...
We're trying to use multiple nRF52833 devices with a single BLE Central (Android tablet) where the devices remain disconnected most of the time, and report back to the central...
Hi,
I've been upgrading a product we designed some years ago with the S110 softdevice on an nRF51822 to use S130 and nRF5x SDK version 12.3 so that we can use the more modern...
Is there any precompiled binaries available to transfer the Thingy:91 sensor readings via usb serial like( temp, humi, pressure, light, accel, gas, lat&lng), right now I'm...
Hello, been trying to get Mosquitto MQTT Bridge working on EC2 (where mosquitto is running). https://docs.nrfcloud.com/Guides/Messages/SetupMessageBridge/#message-bridge-setup...
Hi
Gazell libraries are provided in <SDK>/components/proprietary_rf/gzll/gcc/ and I have 2 questions about those a) I see 2 flavours: gzll_<$HW>_gcc.a and gzll_<$HW>_sd_resources_gcc...
