Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
We are trying to connect to an AWS MQTT broker using the nRF9160 with modem firmware version 1.2.3 and are not having any luck.
Project background:
Using...
Hi Team,
Setup:
Application: smp_svr with overlay-cdc.conf
Board: nrf52840dongle_nrf52840
NCS: 1.7.0
System: Windows
Tool: mcumgr
I am trying to upload an...
Hi, I have a firmware that runs well on nRF52833 dev kit (SDK 17.02) and I am trying to port it to a BL653 dev kit. The firmware has a bootloader and it can perform DFU over...
Hello，I am using nrf24l01+ product for FCC certification, it requires a modulated carrier. If I send this modulated carrier in the form of data packets, it is not a continuous...
Dear ,
When i use the demo of ".\SDK\nRF5_SDK_17.0.2_d674dde\examples\peripheral\twi_scanner\pca10040\blank\arm5_no_packs", Some exception occured . The sdk enters dead...
Hi
I'm running into this error when enabling the soft device (see title). I've read about the PREGION[0] and that, if the info variant is > 0 it indicates a soft device...
Hi,
My device was designed with SDK 15.0, the APP_ADV_DURATION is set to 0 in order to have the device in advertising for all time.
Now I try to use the SDK 15.3 but when...
when told the problem,I wanted to tell the you information . I use NCS 1.7.1 version,OS is windows 10,nrf connect for desktop is 3.10.
Firstly,I install the nrf for vecode...
The newest version that will run on my mac is 3.8. any never version will just freece at the startup window.
...but the programing app crashes when I try to add a file in...
Hi,
I am using the RSA sample code and I need to make the key persist. When I try to change the lifetime attribute to PSA_KEY_LIFETIME_PERSISTENT, the key generation fails...
Hi, I am developing a device using the nRF52832 mcu. I have written my application and have interfaced with an external I2C Sensor. It works perfectly on the NRF52-DK, I get...
I am using NCS v1.9.1 with the nRF52840 and I am not able to move the MCUBoot secondary slot to SPI flash.
I have been able to communicate with the device over the SPI...
Hello,
The nrfjprog command is used for the nrf51822 / nrf52833 program.
Suddenly, nrf52833 shows the following error.
Even though family is specified, it is the same...
Hi,
I'm working on NRF52840 DK , S140 and I'm trying to send large data (around ~64KBytes) from a peripheral device. I'm using the following functions: - sd_ble_gatts_hvx...
Hi Everyone,
I'm currently testing the battery service with my development kit, nrF52dk, and I've found an error stating "The handle is invalid" when I press the "read"...
