Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I am using the Nordic PDM library to collect data from a digital microphone. I am currently storing the data in a 1k int16_t buffer and attempting to store the data...
Hi,
I try to install nrfconnectsetup330ia32.exe on my Windows-10 x64 bit computer. The setup program hangs when the progress bar is at about 33%. It just sits there without...
I am currently working on Nrf52840DK board trying to run ble_uart_app. Designed my board and I used BT840 instead of Nrf52840DK . After, code in NRF52840DK is working but...
Using a Thingy!91 (v1.0.0 and v1.4.0, firmware 1.2.3, 1.2.7) I get sometimes (every couple of days) a ENETDOWN when sending data out. Before that ENETDOWN, the device was...
Hello,
I've been working with NRF52840 for a while now. Recently I decided to add extra options to your code so I went to the development kit for a quick test and debugging...
I cannot get the esb ptx sample to compile on NRF52833 device when using VS Code v1.64.2 running windows 10 64bit .
I've installed everything according to videos, and when...
I am developing a nRF52832 based project where I want to position people indoor using an smartband (where the nRF52832 is placed). I was planning to use beacons so I can change...
Hello,
I have a ported a project from Keil (uVision) to Segger Embedded Studio. Everything is compiling, but unfortunately I have a problem with the linker I cannot solve...
Hello,
I am looking for some advices for a personnal project.
I would like to be able to receive all BLE packets ( so all protocols (GATT, SM, LL) and not only GATT) that...
Hi Nordic team,
I have used the nRF5340 BLE Online Power Profiler extensively in the past for things like estimated event energy and estimated battery life. Do you have...
Hello,
I use the nRF52840DK with direct programmed registers for NRF_RADIO peripheral to send and receive 802.15.4 frames. I have also a separate laptop with nRF52840 USB...
Dear all,
We're developing a custom HW with several nRF52832 chips on one board. For convenience we applied third party module instead of building minimum system by ourselves...
Hello,
in our device we use the Timeslot API to share a 802.15.4 based protocol with BLE, softdevice is S140 6.1.1.
Problem: the 802.15.4 protocol misses appr 10% of the...
