Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
The ZB_ZCL_VERSION define in the file zboss_api_zcl.h have a bad value in the SDK NRF 5 v4.1.0 In the documentation, it is mentioned that :
The Nordic Zigbee software...
Hi!
I did a mesh trying to use diferent versions of a project renaming them, deleting the files inside the folder where I have my projects, putting inside other projects...
We're using nrf Device Manager for mobile to perform DFU over BLE to an nrf5340-based module with firmware built using the nrf connect 1.6.1 SDK and the out-of-the-box Zephyr...
Why there are multiple resets after post validation, firmware activation, etc in firmware update process? Can it not be handled sequentially without resets?
Hi,
We are trying ble_app_uart example for nRF51822 with nRF5 SDK v12.3 and ble_app_uart_pca10028_s130.hex file provided from hex folder works fine, but when we open IAR...
Central nRF5 device connects to peripheral NCS and initiates bonding.
The peripheral reports that security failed with error code 4 (BT_SECURITY_ERR_AUTH_REQUIREMENT) "The...
Hi all,
I am a beginner of nRF5340, trying to test AoA function for indoor positioning.
I'm wondering if there is any helpful document that goes through the whole process...
Hi there,
We are developing on the NRF5340, and have a question regarding programing. You cannot program a core, while Nordic is only powered by Vbus. When I give Vbus power...
Hi,
I have a idea but at the moment not the right approach to do it, thats why I ask here.
I want to store the current time somehow on the device so it survives a reboot...
I am working in a project where we want to be able to do full modem firmware update with FOTA for modem version 1.3.x. According to the release notes, in order to do this...
hi, i am using ncs 1.8.0 for an application where i need to send some data every 10 ms. directly sending data over NUS with bt_nus_send() from the main thread works fine....
While trying to debug some issues with my board I accidentally programmed by custom board while powering it with only 3V and now whenever I try programming it I get the following...
I want to send some data to client from server when I received data from client using server_set callback function.
Means I want to reply to client some other data then...
Hi Nordic,
I am using SDK 15.3. While I am working on a central, which connects 2 periperial devices simultaneously, I found a id_manager.c issue, protentially a bug I guess...
