Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
We are using public MAC that was purchased from IEEE (20 low bits are available for us to set and the upper 28 bits are constant to value assigned to us by the IEEE).
We...
Hello Community, I'm using the current sensor INA219 with NRF5340dk. Communication is through i²c protocol and using nrf SDK v1.8.0 . I'm trying to get the data output (Bus...
Is it possible to override ZEPHYR_BASE when building with the nRF Connect extension in VS code?
I am using workflow 4 (application as manifest repository) and can build...
Hi DevZone.
We have problems with our NRF52833-DK We believe they are damaged because under normal conditions, they normally draw less current (.001 A). It is normal to...
Hello Nordic. I'm using the nRF9160DK and with it, some sensors and an sd-card. I save data to the sd-card using a fatfs filesystem, the files are of magnitude 500 kB. I want...
Is the button (from Thingy52 black case) the only option to trigger an IFTTT? Can I use the sensor's information to trigger an event with the IFTTT? like if the temperature...
Hi,
I am merging a PWM_driver example with a ble-peripheral-blinky example to generate PWM signals with user-defined arbitrary phase-shift and duty cycle.
I am done...
Hello,
I have nrf52832 platform and my version of softDrive is (nRF5_SDK_15.3.0_59ac345).
My problem is regarding GPIO configurations are NOT retained ,when the nRF52832...
Dear Support term:
The Restful of Nrf Cloud is not work.
The node should have more that 100 data, so get ListMessages should give us pageNextToken.
Yes the result give...
Hi all,
I am using a custom board with NRF 52840 with SDK15.2 as slave and STM as master. I cannot receive right data, but the data to STM is right.
The above are...
Hi,
I am using an nRF52833dk to run a simple async SPI transceive API using k_poll My code is as below, for some reason it always returns BUS FAULT error Code:
Error...
Hello,
I face at least 2 problems and need some support.
What I want to achieve is that the DTM runs at our customer hardware for radio and later on BLE certification...
Hello !
In PS1.7 chapter 6.4.5 Encrypting packets on-the-fly in radio transmit mode is explained encryption of a short packets (MODE.LENGTH = Default).
But when MODE...
Hi there, I'm performing an throughput analysis using an nRF52 development board (BMD-350) and a Raspberry Pi 4B (Ubuntu 20.04, BlueZ 5.54) with an BLE 5.0 adapter. For measuring...
Hi,
I want to use the bsp button to our project, so I tested on the example "ble_app_blinky",
I modified the app button to bsp button, add two custom events to the bsp_event_t...
