Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I facing a problem. When, progrsmis run for testing on nRF5340DK using SES, the CPU resets automaticaly. The RAM does not respond timely is shown , please see the attached...
Hi everyone,
There is an open ticket that I need support with because the responsible engineer will be out of the office until the new year.
In a nutshell:
I design...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Please tell me about "nrf_sdh_enable_request". This API only makes a request, so I understand that the SoftDevice...
Hello Respected members, I hope this post finds you well. Can someone help me with how to store UART data in FLASH? The Idea is that I have to send the Date Or Serial Number...
Hello !
As part of nrf_crypto it is no any examples how-to use chacha20 without poly e.g only stream cipher.
Would be nice to use it via nrf_crypto and evaluate hw accelerated...
Hello. I had worked on nrf52840 development kit with BLE UART code(pin 6 and 8 as Tx and Rx). I used the same code on Fanstel EV BC840M board. I changed the Uart pins to 9...
Hi,
we are considering the Serialisation library for the SoftDevice S132 in one of our projects and would like to know for how long this library will be supported?
Thank...
Hello! I have made good progress in studying nrf9160, and nRF connect SDK but....
I'm having problems with basic things. I want to create a project in the nrf connect sdk...
The Project (on a NRF52840) is setup to use an external toolchain (for C++) and we use the S140 softdevice (v7.2.0) for BLE stuff.
1. without loading the S140 hex file and...
Hi,
In nRF_SDK_for_Thread_and_zigbee, we were using the following function to enable thread coap in both server and client role in a single node:
I want to implement the...
Hello,
i've two nRF5340DK (QKAAD0 2050AC),
1.when using NCS1.8 create project, cupapp / cpuapp_ns / cpunet Which option is it?
2.how to know it is 128 or 64 MHz Arm...
I'm seeing an issue where a Mesh Proxy node temporarily stops relaying mesh packets to other nodes. The problem seems to persist for roughly an hour at a time. In other words...
Hello !
1. In some legacy code I have found that radio channel is configured twice
NRF_RADIO -> FREQUENCY = channel;
NRF_RADIO -> DATAWHITEIV = channel;
Can...
Hi,
I would like to port an existing contiki-ng code to nRF Connect SDK. Within this code, I need to sample the 2.4GHz radio RSSI value around 50000 times in a short time...
