I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Morning Everyone,
We use raspberry pis as part of our test equipment. The final stage of our CI/CD pipeline downloads the build dfu packages to a Pi and then does an OTA...
Hi,
I try to run SDK17.1 examples/dfu/secure_bootloader/pca10040_uart_debug.
Only UART example does not have softdevice.
I build and run that example on SES on M1...
Hi,
https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink
I have tried the example you modified. It works fine. However, I get ERROR 17 NRF_BUSY when 2-3...
Hi Sir/Miss,
I encounter a problem which is in programmer software.
When I open software and connect to nRF52840 DK. Right flash size window will display some animation...
Hi,
Is it possible to send data on Connected mode and in parallel also send the periodic data ?
I tried to implement that but it fails to send in data on Connected...
Hi,
We setup a mesh network with 26 sensor devices, configured these 26 devices into one group. From the mesh gateway device, it sends group message to these 26 devices...
Hi there,
I'm currently using SDK 17.1.0 with the NRF52832 Development Board. This is pretty new to me, but the examples helped me get an application going pretty quickly...
I'm using a nrf52840dongle board with the prj_no_dfu.conf configuration with the following additions:
CONFIG_BOARD_HAS_NRF5_BOOTLOADER=n CONFIG_CHIP_LIB_SHELL=y CONFIG_LOG...
Dear Nordic Engineers
I install nrf command line 10.1.6.0 in my office PC.There was a problem after the installation complate.
I input "nrfjprog" in powerShell ,it's normal...
Hello,
we have a remote control with 7 buttons.
Every button shall wakeup the device from deep sleep.
Beside i will have an interrupt on Button 6 and 7.
So the problem...
I am using nrfconnect 1.5.1 (zephyr/command line) with modem firmware 1.2.3 and believe I have found a fairly serious bug/behavior in the UDP API. It is pretty easy "crash...
Hi,
I looked at some of the questions on the forum and they didn't give me good advice. Currently all I can do is nrf52832 Security 1 Level 4 and nrf52833 Security 1 Level...
In the nRF5340 product specification version 1.2, I see an internal bandgap reference error range of -1.8/+0.5%.
In the nRF5340 product specification version 1.2, I see...
