Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi
I modify the ble_app_uart_c example to support connecting multiple nus peripherals.Calling the new_cccd_configure(p_ble_nus_c, true) return error after nus_c discovers...
Hi,
I am using nRF Connect 3.9.1 and power profiler 3.2.1. I have noticed that if I have a measurement on-going and go away for a while (4mins tested while writing this...
Hi,
I am using an nRF52840 with SDK 17.0.2 and S140 7.2.0. I am running a scheduler based on app_scheduler.
I am trying to make my FDS implementation blocking as it...
hello ;
i am new for nRF52840 DK , i just want to learn how to use it , i need to deploy to bluetooth (ble5) on nrf52840dk to connect or send the data to esp32 , however...
Hi All,
Due to chip shortages we have to replace nRF52832 with nRF52810 in our design. Our application has to perform BLE scanning, but no other functionality of a BLE central...
My nRF is a central and the iOS device is the peripheral. the nRF connects to the iOS then checks via pm_conn_sec_status_get() if pm_conn_sec_status_t is encrypted, if not...
Hi I work with ble on nrf52833 I want to send my collected ble datas with uart1.In my code poll out working but fifo fill doesn't work. Any basic simple for fifo fifo fill...
Hallo,
Is nRF52840 good choice for the wireless protocols such as BLE, Zigbee and IEEE802.15.4? Can I develop these protocols in this SoC? If so is there any tutorial...
Hi All,
I have a question that when BLE connected it will show an error.
Accroding to the error,it show main.c : 163 have problem.
This is a characteristic in my...
Hi i am developing a project on custom board with mcu as nRF52833 module. This board needs to communicate with GPS module and Sim Module, so I need to use 2 UART ports to...
Hi, I am developing an application using Zephyr for nRF5340CPU. In the program there are the statements inserted to conditionaly display few parameters on norma 16x2 alphanueric...
I recently acquired an nRF52 DK and from what I have found on the Nordic site I inferred that I should install SES and VS Code and then later I found nRF Connect. They all...
tried to modify examples/ble_central/ble_app_hrs_c to collect blood pressure but found that there is no ble_bps_c folder in components/ble/ble_services/
Hello.
nRF52832
nRF5_SDK_17.1.0_ddde560
target ble_app_hids_keyboard
1. I made bonding between nRF52 and Android. and connected.
2. I remove bonding in nRF52....
