Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi all, I am using the nRF52832, Mesh sdk v4.2.0 and the nRF5 sdk v16.0.0. How to dynamically change the GAP name of device when using smart phone (nRF connect APP)to scan...
Hi, I'm following the steps on https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_gsg_ncs%2FUG%2Fgsg%2Ffirst_test.html
But in Programmer, the read, write, erase&write...
Creating a second advertising set with bt_le_ext_adv_create will generate an error -12.
Using nRF Connect SDK v1.8.0
The second advertising set is use for FOTA update...
Hi all,
i'am using nrf_Connect_sdk when i write this api
device_set_power_state(); it gives me undefined symbol
i enable CONFIG_TICKLESS_IDLE =y in prj.conf it gives...
Hello,
My company is evaluating the Thingy:91, we're interested in Multicell location lookups. My question is regarding the SDK, specifically if it's possible to configure...
Hi, I am unable to download my program and there's no detailed error messages, if any at all. Can someone please tell me what's going on?
Load "C:\\projects\...\\nrf52832_xxaa...
My company is creating a custom board using the 9160 and 52840. I have a BLE app running on a nrF52840 board that I want to port to the 52840 on the 9160 custom board. And...
I'm a newbie (few weeks) with nRF9160-DK and using nRF Connect SDK v1.7.1 / VS Code on a Windows 10 PC
Good afternoon,
I'm struggling with how to set up and start the...
Setup:
- nRF52832 , Softdevice s132, gcc
- iPhone is the peripheral. A custom service is implemented **on** the iPhone.
On the nRF:
- `#define NRF_SDH_BLE_VS_UUID_COUNT...
Hello.
We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
I am creating a function to connect to a central device, have the characteristic set...
Hi,
I am flashing Blinky led hex file on the flash at 0x5E000 location.
And again if i try to flash the different Blinky hex file at the same location. it wasn't working...
Hello,
I could use some guidance on where to look for a power draw that I am not understanding. I am not a hardware engineer but have been tasked with completing firmware...
