Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I noticed in Zephyr OS there is an API LED:
led_on(dev_io, RED ); <-- does not work gpio_pin_set(dev_io, RED, 1); <-- works well
what can be the reason ?
can you...
Hello everyone. I have just started with the eval board uBlox NORA B1 (NORA B-106) and I am trying to find a starting point for streaming audio via Bluetooth Handsfree protocol...
Hi Nordic：
I use the LWM2M of NCS and found that the power consumption increases every 2.5 seconds. I use the monitor to find that the serial port is sending data. How...
We are attempting to deploy a system consisting of one nRF52840 devkit running the multi-NUS example app, and over a dozen custom boards based on the nRF52832. It all works...
Hi all,
Can anyone guide me to the right path where I can get how to interface an E INK DISPLAY(ET014TT1) to the NRF52840 DK board or tobwhere I can get the necessary steps...
Hi,
I am trying out the FOTA feature on the nrf52840 dongle. I managed to build the SMP server example and flash it using mcugr. However when i reset the device, i can't...
We are evaluating nRF52832 for our next product. One of the requirement for us is to interface 3 set of sensors with nRF52832 over I2C.
Because our sensors can't share the...
Hello, I'm modifying the ble_peripheral/ble_app_hids_keyboard example on a custom board. When I pair my board with the first phone, it works fine.
But I can pair it with...
Hello, I would like to implement an acceleration interrupt in the asset-tracker2 program (SDK v1.7.1) that is executed immediately on movement. This should be executed in...
Dear, I defined Port1 pins as in attached overlay file. The binding of pins is done as in lcd.h attached file. When, build is started, the error written in title is displayed...
Hi,
for a last year I was developing any apps for nrf52840 in Keil IDE. Now I'd like to migrate my projects to VSCode but still do not understand some curcumstancies:
...
Dear NCS experts,
I'm working with NRF Connect SDK (1.7.1) on a proprietary Bluetooth Mesh model. When the model receives its configuration, it stores it in flash by calling...
Hello,
I am evaluating the DK52 board and have a problem with the reset button. Before the problem occurred, when I powered up the board connected to my windows 10 host...
Hello,
We have designed a product with NPM1100. With the NPM1100 set to output voltage of 3.0, we have measured the output across multiple devices to be in the 3.1 to 3...
Hello everyone , I am interfacing and trying to process GPS data received over UART port. The GPS outputs NMEA based sentences at a rate of 10 Hz. I started using the example...
