Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I developed a custom board using nrf52810-qfaa, i edited pca10040e-s112(sdk17.1.0) and changed the advertising led to BSP_BOARD_LED_3, as i have only one led on my board at...
Hi,
I am trying to debug ESB packets with the following setup:
1. PRX (NRF52810)
2..PTX (NRF52810)
3. Sniffer (NRF52832) ( modified PRX so that it returns without...
hi ,
i am developing a zigbee network and i have used the the sample project of zigbee light bulb, switch and coordinator given in nrf5340dk. now i am facing issue with...
Hi,
I'm implementing a FOTA update procedure for the nRF9160 using the download_client from the nRF Connect SDK 1.9.1 and modem firmware 1.3.1.
In general the image update...
Hi,
I am using the nRF52840 DK to connect to an external board via the P20 shield debug out. I was wondering if any indication is given if a board is connected correctly...
Help me please!!!
nRF52840 DK stops to scan after 3 hours working.
Project is based on central_nordic_uart_service.
Scan params
it works fine 3 hours and then BLE...
The linker script for the example code "Secure bootloader ble" for pca10040 have the FLASH section defined as:
FLASH (rx) : ORIGIN = 0x78000, LENGTH = 0x6000
According...
Hello,
I am using nRF5340 with NCS1.7.0 and nRF RPC lib for intercore communication for our product development. I followed this example ( https://github.com/nrfconnect...
Hello,
I installed NCS 2.0.0 via toolchain manager (Windows).
However, if I:
open a new cmd window
set ZEPHYR_BASE to <ZEPHYR_NCS_2_0_0_PATH>
try to build an example...
For study purpose, I try to change bootloader to move APP offset by
change APP start address to 0x20000
change start_addr in nrf_dfu_mbr_irq_forward_address_set() and...
Hi Team,
I'm using a nRF52810 board for my project but in that when I upload code using development kit, at that time my device give advertising and what I gave task.
...
Hi,
i have two nRF52833 program for make AOA. One is programe as Tx with "direction_finding_connectionless_tx" and one is program as receiver with "direction_finding_connectionless_rx...
Hi,
I am using the nRF9160 on a custom PCB, SDK version 1.6.1 and modem FW 1.3.1
My Application uses MQTT to send messages to a server at regular intervals. In between...
