I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi nordic:
I use nrf9160 to test the new driver mainly due to the following two problems:
Environment: sdk 1.8.0-rc2 modem: nrf9160_1.3.1 lwm2m CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
Hi There,
I have a question now. If I want to alter the frame format in the data linker, how do I do?
I try to find the source code of the data linker layer in the Mesh...
I am trying to read temperature value from STS30 temperature sensor using this simple code snippet:
During debugging, my debugger stuck at line "if (STS30_read_temp(temperature...
Dear Members, I want to log my ANT+ HRM into SDcard, I tried with flag, but it never goes to main loop, I'm using nRF52840 Code ANT HRM interrupt :
on the main loop...
hello,
i am using nrf52832 with our customized board and i am trying to send 427 characters string at a time using lbs service but it only accepts 200 characters in single...
Hi! I've got over 2000 smartwatches out in the field that are using the nRF52840. The hardware designers thought it was a great idea to expose the SWD pins along with the...
Hi experienced people
I try to initialize twi on pin 44 and 45.
ret_code_t err_code; const nrf_drv_twi_config_t twi_config_top = { .scl = 45, .sda = 44, .frequency = NRF_DRV_TWI_FREQ_100K...
Is there an easy way to get the manufacturing data from an advertisement packet in the 17.1.0 SDK?
I also struggled with extracting the rssi value and ended up using:
...
I'm using nrfx_saadc V2 in nRF5 SDK 17.0.2. In nrfx_saadc_abort nrf_saadc_task_trigger(NRF_SAADC_TASK_STOP); is called regardless of if the ADC is currently running. If the...
Hi!
We're using the nRF52810 chip, so we have a very limited amount of flash memory. We're looking at every opportunity to save some space. We currently run with a modified...
I've got the USB CDC ACM example up and running. I'd like to do something similar on the nrf52840 Dongle but rather than using a UART for the CLI, I'd like to use a second...
hi support team,
customer has one question about USB device to restart manually, because customer need to change the HID descriptor for some reason.
i tried on usb uninit...
I need your help to design the radio matching network on device nRF52805.
Here the reference design: infocenter.nordicsemi.com/index.jsp In this reference design L1, L2...
Hi Nordic Team,
My dev environment is as follows:
nRF58232+ ses+ sdk17.0+ softdevice 132
We are using BLE Chip on custom board
When we flash precompiled hex file...
