Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I am trying to use puncover to estimate the maximum stack size for the created thread.
We also tried the thread analyzer, but gave up on it because it did not seem to be...
My project builds fine in versions previous to 2.0.0. However, in 2.0.0 I'm getting an undefined reference. Any ideas where to look to track this one down?
/opt/nordic/ncs...
I am using S112 softdevice along with SDK 15.1.1. The chip that I am using is nRF52832 and ble uart example
I want to make advertisement non connectable and non scannable...
hello Nordic
i am working with nrf52832, ncs 1.7.1
i am trying to work with external flash driver (25lp128)
so my dts looks like this:
my configs are this:
myboard...
Hi,
For some time I'm developing application for both central and peripheral devices. The Idea is that both devices have a special mode in which they pair & bond and add...
Hi,
I am developing a project that includes transmission and reception in particular timeslots. I checked the radio example in nrf5 sdk and copied the trasmission part to...
Hello, How send media keys like volume to host using usb hid protocol? For example I using usbd_hid_composite example. I add this code #define APP_USBD_HID_MEDIA_REPORT_DSC...
The direction-finding white paper shows an example for the NRF52811.
I have tried the example to get some NON-softdevice based code and several variations thereof and...
Hi, I am using nRF52832 module (GAP peripheral, GATT server) with nRF5SDK, ble_app_uart_pca10040_s112 application.
I need some help on dynamically changing the BLE device...
We are trying to make DFU over BLE with external flash to overcome the large application size. This is what we are looking for: - Use BLE to transfer the OTA image - Since...
Hi,
I am attempting to get the zephyr usb dfu sample located at ncs/zephyr/samples/usb/dfu to work using external flash. I am using the nrf52833 on a custom board in combination...
Dear Forum,
Im sending at-command's from the nrf52840dk over UART to the NRF9160dk.
Hooking up the NRF9160 to the pc directly, every command works fine, but when sending...
Hello,
Up until today I had been developing fine with visual studio code, installed via Toolchain Manager. Then, I clicked "Pristine Build" for the first time in a few days...
Hi,
I need to implement low power mode in my project with an nRF52832. From a general perspective, I want to:
1) boot the device,
2) initialise stuff/peripherals,
...
