Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
The provision button in nRF Mesh is no longer active. It worked yesterday but I think there was a update to the app and it no longer works.
The app finds the unprovisioned...
Hello all,
Four leds are connected to the GPIO (22-25) and gpio are defined and with a simple method within the while loop I can see them working
Next is to use the...
Hi, I am developing nRF52832, ADS1291.
I got the data from ADS1291 normally through SPI communication.
And I applied RTOS by referring to the nRF5_SDK_17.0.0/examples...
Hi,
Is there a way to turn off the reset loop detection on MFW 1.3? It's annoying having to wait half an hour when you are developing...
Kind regards,
Thomas
I am developing on an nRF52811 and I've noticed that I can't set/clear the pins such as the ones in the bracket in the picture below.
I'm using nrf_gpio_cfg_output(pin_num...
My product is devloping in nrf52810 with Zephyr . The flash is too small. At present, using all peripherals, the size of app_update.bin is 55KB. The size of MCUBoot partition...
Hi,
I'm a beginner, I want to do a test that will create a thread by "K_THREAD_DEFINE" marco.
Then I will continuous print "Hello~~~" per second. That's all.
But I don...
Hi everyone.
I'm approacing to the nrf52833 SoC following this official tutorial but when I import the example template the VSCode finds the cmake tool in my espressif ...
Hello,
SDK Version - 17.0.2
Mesh Version - 5.0.0
I'm using nRF52840 DK to build mesh example(light_lc_server & scene_client).
I try to save the scene of the...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1 I have two quick questions. 1) How to add version information(string) when make binary. 2) How can I read version when I finish...
Could you pls advise what control is there over the output voltage on PPK2?
For example, the STM power monitor only supports discrete output voltages such as 1.8V, 2.4V...
Dear Support Team,
I'm trying to test 802.15.4 feature with the precompiled radio_test hex file, but got an error when connecting the CLI through PuTTY. Below is the detail...
I am very new to the Nordic line and I have an nRF5340-DK that I would like to build a basic BLE Remote Control project. The Remote Control must pair with a phone or computer...
