I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I'm doing some changes to the bootloader to be able to copy the old app in bank 0 to another extra bank (bank 2) in case of needing to do a rollback without connection...
Hi,
I am using the nRF9160 DK board and want to use it in offline mode (without IoT Sim or services ),
Actually, I am living in India and here we don't have IoT SIM, but...
Hello, I have been working on trying to get Bluetooth mesh to work in Unity trying to support iOS, Android and UWP. I will have to write most things from scratch. At this...
I have just received nRF52840 dongle and I cannot get it programed. I have tried both west flash and nrfProgrammer from nrfConnect.
I have been developing using nrf52840dk...
I'm trying to add the drivers, etc from here: https://github.com/circuitdojo/pcf85063a for the PCF85063a RTC, to my project.
Part of the process involves updating the west...
I am using the http library, NCS 1.4.1 on nrf9160dk and discovered an issue that was fixed here: https://github.com/zephyrproject-rtos/zephyr/commit/ab2f616641b19684455369b1e2a362eb736774cc...
Hello Support Team,
Our product design uses a custom BLE service and solution with the nRF52832 on our own board. Also, this BLE peripheral device does not use any BLE pairing...
Good morning,
To my knowledge, the nRF52833 dk as well as the reference designs are FCC certified.
I'm currently searching the FCC IDs for these designs but I'm not able...
This example automatically create the thread network. Once the button is pressed every 3 second udp is sent.
Issue is I am not receiving the packet on 2nd device. I am not...
Hello, we came across a recurring issue:
There are no executable permission for Linux + macOS for the packed binary:
jlinkarm_nrf_worker_linux
jlinkarm_nrf_worker_osx...
Hi,
I have written the BLE UART code With custom characteristics. I have flashed the code to DK and tested it. but that was not working correctly. Then I flashed the sample...
Let me start by saying we have not ruled out other possible sources of errors at this point. However, right now all the evidence is pointing to an issue with the nRF52840...
I attended the Introduction to the nRF21540 RF FEM for range extension webinar and bought a few nRF21540-DB kits
The first thing I want to do is compare the range increase...
Hi,
We have our own MQTT broker setup with TLS running on a AWS EC2 cloud service. I am building my code based on the MQTT_SIMPLE example. I have only a CA certificate in...
In my project I use nRF52832 embedded in MuRata module. I have a BLE service with capabilities very similar to NUS service.
I've managed to add support for LESC + SEC_MITM...
