Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
We are having connection problems with our nRF52832 based HID device only on Windows. I've attached packet captures taken with the nRF sniffer (nRF52 DK) and in Windows with...
I am using nRF52 DK and LIS3DH accelerometer.
LIS3DH configuration is as follows:
1. LIS3DH ODR set at 10Hz,
2. Low Power Mode (Low resolution),
3. Acceleration: 2g...
I am registering interrupts for many pins:
This only works for the first 8 pins, because from what I understand the GPIOTE peripheral is used and that has only 8 channels...
Hi
I am trying to program a nRF5340 device using programmer 3.0.0. But when I try to connect to the JTAG I get the below error.
using nRF Connect for Desktop v3.11.1 ...
Hello
SDK starts adverting when reset. I want to start adverting at the push of a button.
SDK version : 17.0.0
SWDevide : s112
When the button is pressed as above...
Hi everyone,
I want to send large data with https protocol.
I edited the https_client sample split the data and looped send() for sending the large data.
But when...
Hi all
I have an issue regarding central- peripheral connection.( using nRF52832)
In the past I developed a peripheral device using SDK 11.
In order to manufacture it...
Hello, I am doing a bachelor thesis using the nRF52 Development Kit to control a (RC ) car, and I am 3D-printing holders for extra peripherals. During the 3D-modeling and...
When I run nrfjprog --pinreset it says "Applying pin reset" but it has no effect on the connected nRF52832, it just continues running. Other nrfjprog operations like reading...
I am working on Apple Macbook Air with M1 silicon and I installed nRF command tools version 10.15.4macOS
When I open the toolchain manager , there is an error that shows...
Hello,
I am trying to get reliable log output using the Nordic Connect SDK (NCS) over RTT. When I use Minimal mode, the following config:
CONFIG_LOG_MODE_MINIMAL=y CONFIG_SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL...
Hi All,
Sorry for such a very basic question, but I've tried many things and combinations and cannot make this work.
I'm trying to discover BLE sensors using nrf_ble_scan_init...
Hello,
I am using the Zigbee NCP sample from the nrf Connect SDK and I would like to change the uart baudrate. How can I achieve this? I tried to find some configurations...
When I try to debug hci_pwr_ctrl in Zephyr/buletooth/sample using segger embedded studio, debug terminal don't have output of printk function, which based on nrf52840dk. ...
Hello All,
I am experiencing strange results when using the TWIM peripheral with and without using the debugger.
Setup :
Keil IDE for development and debugging ...
