Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi,
I see that the NRFX_SAADC_CONFIG_LP_MODE macro sets the default low_power_mode member for the nrf_saadc_config_t struct used to initialize the adc. What I cannot figure...
Hi Nordic Dev Team,
I've got an application where I want to store two types of log data in my memory flash that I want to send to server eventually via BLE mobile app. ...
Hello, I recently did a ble project, it requires pairing and binding ,
1， I can't find ble central demo
2, The ble central of 52832 will connect to multiple slaves, and...
Hello there,
I am using the rtc2 in NRF52832 to interrupt at randomly generated time instances. Now, I am trying to integrate this functionality in a framework that uses...
I would like to use the low power pwm library to get a breathing LED effect on my device. The MCU I am using is a BMD 350 and the LED is connected to nRF52 port P0.02.
...
I want to protect the programme and data in the flash memory from being rewritten during shipment.
I thought that I could set the NVMC register, CONFIG, to read-only, so...
today in the morning I can connect this web site via chrome.
but I cannot connect this web site few hours later with banned my ip page.
I don't understand.
my system...
I am working on a project that requires serial DFU without flow control using nRF SDK 17.1.0 running on the nRF52840 without the soft device as I don't need BLE for this application...
We are investigating the use of the Soft Device Controller as an alternative to a Soft Device for our production product. Using our BLE stack we have successfully completed...
Hello!
I am trying to install MCUMgr on MACos.
I install the Go Programming Language and then follow this: https://docs.zephyrproject.org/latest/services/device_mgmt/mcumgr...
I'm using SDK 17 with the nRF52840-DK.
As a starting point for my application, I'm using the .../examples/ble_peripheral/ble_app_hrs_freertos project since shows the proper...
Hello, I would like to make a follower robot. For this, I wanted to use the AoA to locate my phone and thus determine the direction in which the robot should go.
I'm really...
Hello,
I am working with a nRF5340 and need to use both CDC and mass storage on SD Card. I started my application based on the CDC example and it has worked fine.
Now...
Hello,
NCS1.9.1, VSCode, nRF52840,
from link UART Driver – Nordic Developer Academy (nordicsemi.com)
uart can't to receive data continuously,
receiving evt->data.rx...
Hello,
I am working on nRF52840 DK and dongle. I am trying to implement a firmware that can scan device and send command through NUS. So I use ble_app_interactive example...
