I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi everyone,
I'm currently using nRF52832 with nRF5DK_V17.1.0 file.
I understand that this question has been risen up quite a lot however, I still do not understand why...
Hello Nordic team,
I am testing a timer using code snippet which Nordic team recommended as a reference. My code is something like this:
uint64_t start, stop;...
Hello,
A nrf52840 central device programmed with Soft-Device S132 and connectivity firmware, the host is interfaced via USB and uses PC-BLE driver API's to communicate with...
Hi,
I'm using nrf52840 DK and android based mobile with nrf connect for mobile app installed.
I would like to execute a freestanding sample code to transfer message between...
Hi Nordic,
I met a issue on BUS FAULT , which caused by queue.
It core dumps that:
[2022-03-22 15:35:12.657] [xxx]index = 6,len = 158 [2022-03-22 15:35:12.660] [xxx...
Hi all,
I'm a beginner and planning to import Android-nRF-Toolbox source code from Github into Android Studio after reading the README by the following steps:
1. I open...
Hi Team
In nRF52
According below picture the only the power on reset and brownout reset can reset SWJ-DP. Do we have any other method to reset the SWJ-DP.
By the way...
Hi there, We have a product using an nRF52832-QFAA, with the SDK15.2.0, the 132 Softdevice, and an application based around the Nordic UART service (nus). Customers are reporting...
Hi everyone,
i'm writing to ask some advice for my NBIOT AWS application with the nRF9160 DK.
I'm currently using the aws_iot sample available as a baseline for my project...
Hello,
We observed that the BLE-Mesh provision logs are happening in FCBs of NV Flash, For my application i need them to be logged on RAM. Kindly suggest how I can achieve...
Hi everyone,
I am working on a project, in which I have n nodes that communicate with each other (peer to peer communication). In addition, each node is able to communicate...
under freestanding applications, which code to use to enable bluetooth on nRF52840 DK kit . Then, it has to pair with android mobile. how i can achieve it.
I see mainline Zephyr is now on v3.0.0 since end of Feb. I assume the bump from 2.7.x to 3.x means substantial changes. When will NCS move to a 3.x zephyr?
I ask this...
Hello.
It is being developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
Previously, I inquired about how to add a value to the characteristic with...
