I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello,
I have a running thread network now. Yay!
I am using a BMD-341 module from a old board as a Thread Sleeping end device. Getting great results.
I've flashed the...
Hello, we have made 50 cards with your microcontroller,out of the 50 cards there are 6 cards which consume about 10µA in sleep, while the others consume less than 1µA. Have...
Hi All,
We are using NRF52832 for our project.
We are using LED driver based on I2C protocol.
Do we have example code for I2C driver?
Please send some example/sample...
Hello,
I've installed nRF Connect for Desktop for Mac and from the UI using the Toolchain Manager I've installed nRF Connect SDK v1.8.0. After installing the extensions...
Hi,
I have been developing an application that reads sensor data (over SAADC and SPI) over an interval, serializes the data, and transmits the data over BLE_NUS to a companion...
Hi Nordic,
when I enable the Bluetooth configuration, the sensor trigger stop to work. when I comment the Bluetooth configuration, the sensor trigger back to work.
I recorded...
hi support team,
for nrf5 sdk ble_app_hid_mouse example, this example shows how to use swift pairing, it works. but I have one question for it, after I press reset button...
Hi, I'm trying to run samples provided by Nordic but I fail. My problem is west can not find my Jlink.
I can flash the chip (nrf52840 custom board) using nrfjprog
...
1. When I run the SDK routine provided by the official, ble_app_uart program, the circuit board acts as the peripheral , the protocol stack is pre-downloaded to the board...
Hi,
Update MDK to handle APPROTECT, MDK can be downloaded from MDK website, but no details on hot to update MDK to nRF5 SDK. Any guide lines to update the MDK with nRF5...
Hi, I am new with nRF microcontrollers. I created a custom board that mounts the nRF52840 microcontroller. I made a firmware that uses BLE to exchange data and everything...
Hi,
I'm using nRF Connect SDK v1.7.1 with two nrf5430 DK. My goal is to evaluate the different security levels. For testing i send messages with the Nordic Uart service...
According to the AT command reference v1.7, the nRF9160 SIP modem firmware v1.3.1 added the %PERIODICSEARCHCONF command.
It does though not mention anything about the behavior...
We are evaluating OpenThread for a custom board with a BL654 from Laird, which contains an nRF52840. When running the OpenThread CLI sample from nRF Connect SDK 1.7.1 we are...
remoteproc_mgr_config() from nrf5340_cpunet_reset.c that is called during init by zephyr for starting main thread uses hardcoded pin numbers for uart with cts/rts pins and...
